573 Ergebnisse
HMF2525 / HMF2550 - Using burst mode with infinite repetition HMF2550, HMF2525, burst mode, infinite repetition HMF2525 / HMF2550 - Using burst mode with infinite repetition HMF2550, HMF2525, burst mode, infinite repetition Related Products
How to install multiple version of ELEKTRA.
How can the transducer be imported from Excel into the InstrumentView software?
How can I query the waveform data of the serveral segments?
The student team from Cellsius Project H2 uses an R&S®RTA4004 oscilloscope to validate the functionality of its inverter.
Read this educational note and dive into the discussion about the six most important transformer measurements: turns ratio, mutual inductance, phase angle, primary and secondary inductance, leakage inductance, and interwinding capacitance.
28.02.2024
This application note addresses the diverse possibilities of interoperability between Rohde & Schwarz power sensors and Rohde & Schwarz signal generators. All current and many legacy Rohde & Schwarz signal generators offer the capability of directly connecting power sensors. This enables power measurements without the need of a base unit or separate PC to display the readings. Furthermore, sensors can be used for special tasks like filling a user correction table or continuously controlling levels at crucial points in the measurement configuration.
31.08.2023 | AN-Nr. 1GP141
The student team from Cellsius Project H2 uses an R&S®RTA4004 oscilloscope to validate the functionality of its inverter.
The overall concept is explained using a product demo of a 5G TSN juggler which shows a deterministic low latency communication via 5G and ethernet using time sensitive networking(TSN).
The power consumption analysis tool was developed to make it easier for customers to analyze power consumption data collected with either the NGL, NGM or NGU power supplies from Rohde & Schwarz. It allows to easily capture power consumption data and analyze using basic measurements.
31.01.2022 | AN-Nr. 1SL380
In the satellite sector, components, subsystems and entire satellites must be qualified in a thermal vacuum chamber before they can be used in space. This qualification proves that equipment can not only survive but also function in the harsh conditions encountered during launch and in space.
05.10.2022
This R&S®FSW-K70 application sheet describes the challenge of determining typical signal parameters of an unknown signal from the results of a basic measurement using the R&S FSW VSA application.
Generating models with a VNA and using these on an oscilloscope via the deembedding
23.05.2023 | AN-Nr. 1SL393
In this document we will describe in detail how to configure and perform path calibrations with AMS32-K81 in an ATS1500C, using an AREG800A.
03.05.2023 | AN-Nr. 1SL399
This video demonstrates the speed, safety and privacy features of the Rohde & Schwarz Quick Personnel Security Scanner and explains the millimeter wave radio technology it uses. QPS demo video Enhanced Technology Solutions for Evolving Security Challenges
MXO 4 - See the difference This video shows you how you can better place and stabilize your probes using the the Rohde & Schwarz 2D positioner for passive probes and the 3D positioner for other probes. This video shows you how you can better place and stabilize your probes using the the Rohde & Schwarz 2D positioner for passive probes and the 3D positioner for other probes.
The R&S®HA-Z24E External Preamplifier Manual describes how to set up the preamplifier, how to read out the s-parameters using the provided software, and how to insert the preampifier in a measurement setup. It also includes safety information and a performance test to check the preamplifier's performance.
Setting up complex real-time trigger conditions using the R&S®RTE and R&S®RTO oscilloscopes increases the test coverage and robustness of converter and inverter systems.
10.08.2020
I perform a calibration with remote commands. With the command to start the calibration sweep with a short standard I get this error message. What is the problem?
A closer look at phase resolution and practical demonstration using cut outs is included.
MIPI D-PHY is a low-power, cost-effective physical layer interface, essential in mobile devices and advanced technology systems. It's a high-speed, source-synchronous interface used in smartphone cameras, smartwatch displays, drones, in-car entertainment, automobile cameras, and radar sensors. This application note explores MIPI D-PHY's features, functionality, and testing practices for device compliance, addressing common issues. It highlights Rohde & Schwarz's equipment for ensuring compatibility and solving issues with MIPI D-PHY, aligned with MIPI D-PHY specification version 2.5.Developed by the MIPI Alliance, D-PHY connects cameras and displays to a host processor via CSI-2 or DSI protocols. It features a master-slave, asymmetrical design for reduced link complexity. Key aspects include a unidirectional clock, optional data signal directions, different data rates for half-duplex operation, point-to-point communication, and high-speed (HS) and low-power (LP) modes for data transfer and battery preservation. In HS mode, D-PHY uses differential signaling with specific impedance, while in LP mode, it operates in a single-ended manner with high impedance termination.The application note from Rohde & Schwarz provides insights into characterizing and debugging MIPI D-PHY, offering conformance verification with MIPI Alliance standards and protocol decoding options.
31.01.2024 | AN-Nr. 1SL410
Christian Müller provides an overview about spectrum analyzer measurements such as uplink interference and Over-The-Air measurements such as 5G cell- and beam-specific and multi-technology measurements using our game changer R&S®5G STS.
This webinar gives an overview of HF propagation, the technical principles underlying NVIS, the different types of antennas commonly used for NVIS operation, as well as the technical and operational aspects of NVIS This webinar gives an overview of HF propagation, the technical principles underlying NVIS, the different types of antennas commonly used for NVIS operation, as well as the technical and
MXO 4 - See the difference Quickly and reliably trigger and decode packets from your SPI bus using either the analog or digital channels as serial bus inputs. See how you can flexibly configure the trigger or display the decode table. Quickly and reliably trigger and decode packets from your SPI bus using either the analog or digital channels as serial bus inputs.
See how the China Academy of Information and Communication Technology (CAICT) conducts certification tests using test equipment from Rohde & Schwarz C-V2X, CAICT, conformance test See how the China Academy of Information and Communication Technology (CAICT) conducts certification tests using test equipment from Rohde & Schwarz.
14.03.2023
CAICT selected R&S CMX500 OBT to enable SPEAG DASY8 system for SAR and HAC tests of 5G NR devicesThe China Telecommunication Technology Labs (CTTL) Terminal labs at the China Academy of Information and Communications Technology (CAICT) successfully conducted specific absorption rate and hearing aid compatibility testing for 5G new radio mobile devices. The lab upgraded their DASY8 high-precision electromagnetic near-field scanning platform from SPEAG, the leading provider of dosimetric test systems, with the R&S CMX500 OBT 5G one-box signaling tester from Rohde & Schwarz. SPEAG and Rohde & Schwarz have been long-term partners with CAICT and have supported and equipped CTTL with testing solutions and provided support.
Quickly and reliably trigger and decode packets from your RS232 or RS485 buses using either the analog or digital channels as serial bus inputs. See how you can flexibly configure the trigger, change the data format or display a decode table.
Quickly and reliably trigger and decode packets from your LIN bus using either the analog or digital channels as serial bus inputs. See how you can flexibly configure the trigger, change the bit rate or threshold voltage or display a decode table.
Quickly and reliably trigger and decode packets from your I2C bus using either the analog or digital channels as serial bus inputs. See how you can flexibly configure the trigger, change the bit rate or threshold voltage or display a decode table.
Rohde & Schwarz offers a powerful tool for remote control of their oscilloscopes - the RsInstrument Python module. This module enables users to control and automate their Rohde & Schwarz test & measurement instruments, including oscilloscopes, through Python scripts or interactive console communication.
14.12.2023