8432 Results
A deep, segmented memory combined with dedicated trigger conditions solves this problem by permitting the acquisition of relevant sequences without long pauses.
01-Dec-2017
This application note describes Methods of Implementations (MOI) for precise, fast and error-free compliance testing of high-speed backplanes.
07-Apr-2021 | AN-No. GFM357
Ethernet communications has been introduced in automotive networks to enable fast and cost efficient data communications.
27-Mar-2015
Correlated time-frequency measurements help optimize gate driving and minimize electromagnetic emissions early on during development.
22-Nov-2018
This application note reviews the measurement uncertainty analysis and traceability for phase noise with the new R&S®FSWP Phase Noise Analyzer.
05-Jul-2016 | AN-No. 1EF95
Measuring RDS(on) with high-definition oscilloscopes - Application Brochure
19-Mar-2015
The R&S®RTx-K36 frequency response analysis option provides a low-cost alternative to low frequency network analyzers or dedicated standalone frequency analyzers.
18-Dec-2018
The alternative approach presented in this paper employs a low phase noise local oscillator for direct down-conversion of the DUT signal.
09-May-2016
The R&S®Cable Rider ZPH, a simple one-port cable and antenna analyzer, can be used to swiftly and easily perform reflection measurements and other tasks.
13-Nov-2017
Models: R&S®TLU9 Transmitter 5 W, R&S®TLU9 Transmitter 10 W, R&S®TLU9 Transmitter 15 W, R&S®TLU9 Transmitter 25 W, R&S®TLU9 Transmitter 50 W, R&S®TLU9 Transmitter 100 W, R&S®TLU9 Transmitter 200 W, R&S®TLU9 GapFiller 5 W, R&S®TLU9 GapFiller 10 W, R&S®TLU9 GapFiller 15 W, R&S®TLU9 GapFiller 25 W, R&S®TLU9 GapFiller 50 W, R&S®TLU9 GapFiller 100 W, R&S®TLU9 GapFiller 200 W
CMUCopy - Transferring CMU Hardcopy to PC using the IEEE Bus or the serial interface
28-Aug-2009 | AN-No. 1MA45
This document describes the direct test mode mechanisms for testing Bluetooth Low Energy devices and explains how the direct test mode connection is established. The R&S CMW uses a USB port for the direct test mode connection while the Equipment under Test (EUT) may provide a USB port, a serial port or even a 2-wire UART interface for this purpose. Installing or assigning the right driver for the EUT is the main configuration task on the R&S CMW. For EUTs with USB port, the R&S CMW provides a Bluetooth Low Energy USB driver which has to be assigned to the connected EUT.
14-Dec-2016 | AN-No. 1C105
This application note describes how to use the R&S CMW platform to perform the measurements defined in Bluetooth test specification version 5.
19-Jun-2017 | AN-No. 1MA282
To ensure connectivity and trouble-free operation, each Bluetooth® enabled device has to be tested for conformance with Bluetooth SIG standards and regulatory requirements.
23-Nov-2017
This application note gives the guidance of how to perform the BLE 5.1 DF RF tests according to the RF test specification of BT 5.1 by using the Rohde & Schwarz test solutions.
30-Oct-2019 | AN-No. GFM327
The Rohde & Schwarz Bluetooth RF test solution with the R&S CMW and R&S CMWrun is closely aligned to the Bluetooth RF Test Suite. This document describes common setups for these tests and the required configurations.
04-May-2015 | AN-No. 1MA261
The R&S®CMW wireless communication tester are ideal for designing and verifying Bluetooth® Low Energy (LE) circuits and modules.
27-Jan-2017
This application note provides a description of the Rohde & Schwarz Click Rate Analyzer software.
15-Jan-2015 | AN-No. 1EE25
Level Uncertainty Calculation for R&S FSV Signal and Spectrum Analyzer
21-Apr-2010 | AN-No. 1EF63
This document describes the adaptive frequency hopping mechanism for improved signaling performance in Bluetooth Basic Rate and Enhanced Data Rate devices.The R&S CMW provides this feature for remote operation in TX, Loopback and Connection test mode. Thereby the R&S CMW acts as a master, while the Equipment under Test (EUT) represents the slave(s) of the piconet.
14-Dec-2016 | AN-No. 1C108
Transmitter and Receiver Measurements on Bluetooth Modules with CMU200
06-Aug-2001 | AN-No. 1MA46
This application note describes methods using an R&S®ZVA network analyzer to accurately measure all the key parameters of frequency converters.
30-Apr-2015 | AN-No. 1MA224
The R&S®RTO digital oscilloscope analyzes RF pulses up to the maximum bandwidth of the instrument used.
09-Nov-2017
Setting up complex real-time trigger conditions using the R&S®RTE and R&S®RTO oscilloscopes increases the test coverage and robustness of converter and inverter systems.
10-Aug-2020
The R&S RTO / R&S RTE digital oscilloscope is a valuable tool for analyzing EMI problems in electronic designs. High input sensitivity, high dynamic range and a powerful FFT implementation are key features for capturing and analyzing unwanted emissions
26-Feb-2015
This application note describes Methods of Implementations (MOI) for precise, fast and error-free compliance testing of high-speed backplanes and direct attach copper cables (DAC).
07-Apr-2021 | AN-No. GFM356
The R&S ® FSWP phase noise analyzer is a highend instrument designed to accurately analyze noise performance of key components in radar and communications systems.
27-Oct-2017
Simplifying mixer measurements with the R&S ZNB
01-Oct-2013