Brochures and Data Sheets for R&S®ELEKTRA

This document provides the technical specifications of the R&S®ELEKTRA EMC test software.

The R&S®ELEKTRA EMC test software can be used to control complete EMC test systems to perform automated or interactive electromagnetic interference (EMI) and electromagnetic susceptibility (EMS) measurements on equipment under test (EUT) to verify compliance with relevant standards.

R&S®ELEMI-E essential EMI test software simplifies electrical product and component testing for EMI characteristics as early as the development phase. R&S®ELEMI-E supports the definition, performance, evaluation and archiving of EMI measurements in line with current standards.

Slide left Slide right

R&S®ELEMI-E Essential EMI Test Software - Product Brochure

R&S®ELEMI-E Essential EMI Test Software - Product Brochure RU

R&S®ELEKTRA EMS test software

New automatic and interactive procedure for measuring electromagnetic disturbances

Convenient management of TEMPEST measurements and reporting. The R&S®ELEMI-T test software is used to measure and analyze compromising emanations. It creates an environment that makes it easier to find, investigate, measure, record and report these emanations.

Upcoming technologies such as 5G for wireless communications and the increasing amount of integrated electronic systems in modern vehicles require new solutions for EMC testing. In addition, manufacturers are looking for time saving test routines and intuitive test software that enable fast precompliance and compliance testing. As a leading manufacturer of EMC T&M solutions, Rohde & Schwarz has a comprehensive portfolio of EMC T&M equipment that ranges from individual instruments to custom turnkey systems.

Slide left Slide right

EMC test solutions on the cutting edge - White Paper

EMC test solutions on the cutting edge - White Paper DE

ELEKTRA, allow device simulation ELEMI-E, ELEMI-EAS, ESEMS-C, ELEMS-R, ELEKTRA, device check, simulate I have ELEKTRA dongle connected to my PC, but some of my devices from Device List are missing. Because of this I would like to simulate my Test, but the button "Simulate" is missing after Device Check. ELEKTRA, allow device simulation ELEMI-E, ELEMI-EAS, ESEMS-C, ELEMS-R, ELEKTRA, device check, simulate

ELEKTRA, pre-define scaling of the graphics ELEKTRA, ELEMI-E, ELEMI-EA, ELEMI-EAS ELEKTRA, pre-define scaling of the graphics ELEKTRA, pre-define scaling of the graphics ELEKTRA, ELEMI-E, ELEMI-EA, ELEMI-EAS ELEKTRA, pre-define scaling of the graphics

Use of ELEKTRA on a non-Test-PC? ELEKTRA, EMC32, non-Test-PC Use of ELEKTRA on a non-Test-PC. Use of ELEKTRA on a non-Test-PC? ELEKTRA, EMC32, non-Test-PC Use of ELEKTRA on a non-Test-PC.

Environment tab on EMCAN64 FAQ, Environment tab on EMCAN64 Environment tab on EMCAN64 Environment tab on EMCAN64 FAQ, Environment tab on EMCAN64 Environment tab on EMCAN64

ELEKTRA: Error message "Failed to copy backup! Folder " does not exist" during backup process ELEKTRA, ELEMS-R, ELEMS-C, Backup I got the error message "Failed to copy backup! Folder " does not exist". Why can't I create the backup without error message? ELEKTRA: Error message "Failed to copy backup! Folder " does not exist" during backup process ELEKTRA, ELEMS-R, ELEMS-C, Backup I got the error message

Automatically park antenna at specific position using ELEKTRA FAQ, Automatically park antenna at specific position using ELEKTRA Automatically park antenna at specific position using ELEKTRA Automatically park antenna at specific position using ELEKTRA FAQ, Automatically park antenna at specific position using ELEKTRA Automatically park antenna at specific position using ELEKTRA

Reference Calibration using ELEKTRA and Field Probe, repeat measurement for a sensor position ELEMI-R; Reference Calibration I would like to do a Reference Calibration using ELEKTRA and Field Probe. For this I have to do Reference Calibrations at 16 positions, this does mean my Field Probe have to be set to each of the 16 predefined points. I set the probe positions manually, so an error can occur

R&S ELEKTRA, use of Open TEM cell for Radiated Emission ELEKTRA, ELEMI-E, Open TEM cell Does ELEKTRA software have possibility to use the Open TEM cell for Radiated Emission? R&S ELEKTRA, use of Open TEM cell for Radiated Emission ELEKTRA, ELEMI-E, Open TEM cell Does ELEKTRA software have possibility to use the Open TEM cell for Radiated Emission?

R&S ELEKTRA, ESH3-Z2 Pulse Limiter's Transducer Factor Entry ELEKTRA, ELEMI-E, LISN, ESH3-Z2 I am using R&S ELEKTRA with EMI Receiver for conducted measurements with a LISN. During installation and first measurement, we had the "IFOVLD" error, what does mean results are invalid. R&S ELEKTRA, ESH3-Z2 Pulse Limiter's Transducer Factor Entry ELEKTRA, ELEMI-E, LISN, ESH3-Z2 I am using R&S ELEKTRA with

Unable to launch Elektra, re-install with clean up ELEKTRA, ELEMI-E, ELEMI-A, ELEMI-S Unable to launch Elektra, re-install with clean up Unable to launch Elektra, re-install with clean up ELEKTRA, ELEMI-E, ELEMI-A, ELEMI-S Unable to launch Elektra, re-install with clean up

Copy the entire database from old version of ELEKTRA to the latest version of ELEKTRA ELEKTRA, ELEMI-S: ELEMI-EAS; ELEMS-C; ELEMS-R Copy the entire database from old version of ELEKTRA to the latest version of ELEKTRA Copy the entire database from old version of ELEKTRA to the latest version of ELEKTRA ELEKTRA, ELEMI-S: ELEMI-EAS; ELEMS-C; ELEMS-R Copy the entire database from old version of ELEKTRA

ELEKTRA: Limit line color change ELEKTRA, ELEMI-E, Limit Line I have created limits lines and used a graph function to show it. I would like to change the color of the limit lines. Is is possible to change the color of the limit line? ELEKTRA: Limit line color change ELEKTRA, ELEMI-E, Limit Line I have created limits lines and used a graph function to show it. I would like to change the color of the

ELEKTRA, Unhandled Exception: Your user name and password are not defined. Ask your database administrator to set up Firebird login. ELEKTRA, Firebird Kindly help me to run the software.After installation, I am getting error message to run the software. ELEKTRA, Unhandled Exception: Your user name and password are not defined. Ask your database administrator to set up Firebird login. ELEKTRA, Firebird

Why is it needed to frequently run backups? ELEKTRA, ELEMI-S, ELEMS-S, Backup Using ELEKTRA I have found a backup dialog. For daily use, is it needed to run backups using this tool? Why is it needed to frequently run backups? ELEKTRA, ELEMI-S, ELEMS-S, Backup Using ELEKTRA I have found a backup dialog. For daily use, is it needed to run backups using this tool?

ELEKTRA, R&S License Server mandatory prerequisite was not correctly installed ELEKTRA, ELEMI-E, ELEMI-EAS, ELEMS-C, ELEMS-R, ELEMS-CRS How can I fix this issue? ELEKTRA, R&S License Server mandatory prerequisite was not correctly installed ELEKTRA, ELEMI-E, ELEMI-EAS, ELEMS-C, ELEMS-R, ELEMS-CRS How can I fix this issue?

ELEKTRA Device List, options displayed in 'General' facet R&S ELEKTRA, ELEMI-S, ESL3, ESL6 I noticed that not all options of the Test Receiver are shown in ELEKTRA Device List. For example, option FSL-B7 is not displayed in Device List. Does that matter? ELEKTRA Device List, options displayed in 'General' facet R&S ELEKTRA, ELEMI-S, ESL3, ESL6 I noticed that not all options of the Test Receiver are

ELEKTRA, restart license server ELEKTRA, ELEMI-E, ELEMI-A, ELEMI-S ELEKTRA, restart license server ELEKTRA, restart license server ELEKTRA, ELEMI-E, ELEMI-A, ELEMI-S ELEKTRA, restart license server

ELEKTRA, Acceptance Analysis not working for a given Limit Line ELEKTRA, Acceptance Analysis not working for a given Limit Line ELEKTRA, Acceptance Analysis not working for a given Limit Line ELEKTRA, Acceptance Analysis not working for a given Limit Line ELEKTRA, Acceptance Analysis not working for a given Limit Line ELEKTRA, Acceptance Analysis not working for a given Limit Line