Search Application Notes & Cards
Learn how to configure Rohde & Schwarz products to fit your application. Search our database by product, technology, or application to find relevant technical documents.
Search Application Notes & Cards
Learn how to configure Rohde & Schwarz products to fit your application. Search our database by product, technology, or application to find relevant technical documents.
93 Results
This application note discusses WLAN standard IEEE 802.11n. It first describes the most important amendments to previous releases and the ambitious new measurement tasks. Then, it describes how to deal with these tasks using Rohde & Schwarz instruments. The main focus here is on transmission over several TX and RX antennas (MIMO). Building multistandard signals using Rohde & Schwarz generators is also described. Screenshots from the analyzer taken on 802.11n signals complete the document.
26-Apr-2013 | AN-No. 1MA179
Even with the introduction of HSDPA and HSUPA, evolution of UMTS has not reached its end. To ensure the competitiveness of UMTS for the next 10 years and beyond, UMTS Long Term Evolution (LTE) is being specified in 3GPP release 8. LTE, which is also known as Evolved UTRA and Evolved UTRAN, provides new physical layer concepts and protocol architecture for UMTS. This application note introduces LTE technology and testing aspects.
14-Sep-2009 | AN-No. 1MA111
The use of Rohde & Schwarz device drivers under VEE software is not complicated. However, a number of factors are involved, the errors that occur are often difficult to diagnose. This application provides easy and detailed support for installation and troubleshooting using National Instruments or Agilent GPIB boards.
20-Dec-2012 | AN-No. 1MA035
This application note describes in detail the steps required to make a noise figure measurement on a spectrum analyzer using the “Y Factor” technique. Background equations are presented for each step of the calculation. In addition, guidelines are provided to ensure a repeatable measurement. Measurement uncertainty is then reviewed, including contributions due to the noise source, analyzer, and the DUT itself. Finally, a software utility is presented that automates the noise figure calculation using four measurements from a spectrum analyzer. The utility checks the measurement guidelines and highlights potential problem areas. It then calculates the noise figure for the DUT along with the measurement uncertainty.
25-Jul-2012 | AN-No. 1MA178
The R&S EX-IQ-Box serves as a digital baseband interface between a device under test (DUT) and Rohde & Schwarz generators, analyzers and radio communication testers. The DigIConf software supplied with the device controls up to four R&S EX-IQ-Boxes in a test setup and can thus output IQ data for feeding into a DUT while simultaneously receiving IQ output from a DUT.To work together smoothly, the DUT, the R&S EX-IQ-Box and the R&S test instruments have to be configured properly. The purpose of Application Note 1MA168 is to introduce the right 'initial steps' required to get started successfully.
23-May-2012 | AN-No. 1MA168
This document provides an introduction to SDR as used for military radios and presents the relevant T&M solutions offered by Rohde & Schwarz.
15-Sep-2012 | AN-No. 1MA206
Signal generators play a vital role in electrical test and measurement. They generate the test signals that are applied to components such as filters and amplifier, or even to entire modules, in order to ascertain and test their behavior and characteristics. The first part of this educational note presents the applications for and the most important types of signal generators. This is followed by a description of the construction and functioning of analog and vector signal generators. To permit a better understanding of the specifications found on data sheets, a closer look at the most important parameters for a signal generator is provided.Beyond the output of spectrally pure signals, a key function of RF signal generators is the generation of analog- and digitally modulated signals. The second part of this note therefore presents the fundamentals for the most significant analog and digital modulation methods.The third part of this educational note contains exercises on the topics of analog and digital modulation. All described measurements were performed using the R&S®SMBV100A vector signal generator and the R&S®FSV spectrum analyzer.
03-May-2016 | AN-No. 1MA225
Miloslav Macko 1MA196 1MA196, Forum, Instrument, Remote, Control, Python, R&S Forum, RS Forum, R&SForum, RSForum R&S®Forum for Instrument Remote Control Using R&S®Forum Application for Instrument Remote Control Miloslav Macko 1MA196 1MA196, Forum, Instrument, Remote, Control, Python, R&S Forum, RS Forum, R&SForum, RSForum R&S®Forum for Instrument Remote Control Related products
28-Jun-2018 | AN-No. 1MA196
Versatile Software Tool for Rohde & Schwarz Instruments
RSCommander is a versatile software tool for a wide range of Rohde & Schwarz spectrum-, network analyzers, signal generators and oscilloscopes. It allows for automatic instrument discovery, making screenshots, reading traces, file transfer and simple script creation.
24-Dec-2017 | AN-No. 1MA074
Software tool for fast and repeatable optimization of signal analyzer RF front-end settings
The signal conditioning in the RF front-end of signal analyzers is crucial to achieve the best performance with respect to image-suppression, noise-floor, dynamic range and other RF-key parameters.Precise signal levelling is especially important for complex measurements like Error-Vector-Magnitude (EVM). To minimize the measurement uncertainty from test system contributions over a wide range of different levels, the RF front-end needs to be adapted continuously according to the signal characteristics, signal power and frequency - ideally using an automatic levelling algorithm.This document describes the approach of a waveform specific, on-site characterization of the signal analyzer: For each waveform and frequency of interest, the instrument is evaluated in a first step. With this additional data, a fast and repeatable auto-levelling can be performed during the actual measurement.
24-Jan-2022 | AN-No. 1EF111
Rohde & Schwarz signal and spectrum analyzers equipped with the R&S®FSx-K30 option form the basis of a solution to accurately measure the noise figure in the millimeterwave frequency range using the Y-factor method.
17-Jul-2017
Wide range of set-top box tests in line with current DVB-xx standards using a variable, future-ready test system
13-Jul-2012
R&S®VISA is a standardized software library that allows fast communications over diverse interfaces with a wide variety of T&M instruments that are detected on the network from PC applications. R&S®VISA also includes a trace tool that simultaneously monitors communications between multiple applications and T&M instruments, and permits targeted analysis with the aid of efficient filters.
26-May-2020 | AN-No. 1DC02
Active, high-impedance probes can be connected to spectrum analyzers, providing a practical and highly precise measurement solution to overcome an otherwise cumbersome RF testing issue. This application note provides information on how to use oscilloscope probes in RF measurements using spectrum analyzers.
04-Jul-2023 | AN-No. 1EF116
This application note explains how to convert different Rohde & Schwarz I/Q file formats among each other using the supplied software tool.
23-Sep-2015 | AN-No. 1EF85
Rohde & Schwarz presents a customizable solution for testing GNSS receivers to ensure a certain resilience against (legal) interference from neighboring bands.
18-Jul-2017
In this day and age of internet of things, more and more devices are connected to the local network, making it even more difficult for the IT department to monitor them. Rohde & Schwarz instruments are also increasingly accessed via their LAN interface, which provides additional convenience features such as remote desktop, SMB file transfer or a web interface. To make it easier to monitor the use and status of instruments, some devices offer a software option, the Health and Utilization Monitoring Service (HUMS).HUMS can be accessed via SNMP and REST (HTTP) and provides all necessary information about the health status and utilization over time in many details.This application note describes how to access HUMS and what data is provided.
11-Jan-2021 | AN-No. GFM336
The Internet of Things (IoT) is considered the driving force of current and future wireless communications. In release 13, 3GPP has specified Narrowband-IoT (NB-IoT) as a new physical layer. This application note gives a short introduction to NB-IoT and shows the easy measurements with Rohde & Schwarz instruments.
30-Jun-2017 | AN-No. 1MA296
This Application Note gives a short overview how signals with two different modulation schemes can be analyzed using the R&S®FSW (or R&S®FPS) using its Multi-Standard-Radio-Analyzer (MSRA) and Vector Signal Analysis personality. The Application Note focuses on DVB-S2(X) signals, but the approach may be used for similar signals as well, as e.g. used in microwave backhaul links.The Application Note also provides a software tool that automates the configuration and provides the variety of different constellations that are used within DVB-S2(X).
18-Apr-2016 | AN-No. 1EF93
conducted conformance testing according to TS 38.141-1, Rel. 15
3GPP defines the Radio Frequency (RF) conformance test methods and requirements for 5G NR Base Stations (BS) in the technical specifications TS 38.141. This application note describes how all mandatory RF receiver tests (TS 38.141-1, chapter 7), according to Release 15, can be performed quickly and conveniently with signal generators from Rohde & Schwarz by either choosing manual operation or a remote control approach. Moreover, one test case requires a signal or spectrum analyzer from Rohde & Schwarz which is highlighted seperately in the corresponding chapter.In Addition, a new Python software library comes with this application note to enable the remote control approach of base station testing. This example requires the RsInstrument module which can be found on pypi.org or installed via 'pip' and is provided as is.
02-Dec-2020 | AN-No. GFM314
3GPP TS25.141 defines conformance tests for W-CDMA base stations (including HSPA+ features). This application note describes how transmitter (Tx) tests (TS25.141 Chapter 6) can be performed quickly and easily by using signal and spectrum analyzers from Rohde & Schwarz. A few tests additionally require vector signal generators from Rohde & Schwarz. Example illustrates manual operation. A free software program enables and demonstrates remote operation. The W-CDMA base station receiver (Rx) tests (TS25.141 Chapter 7) are described in Application Note 1MA114.
21-Oct-2014 | AN-No. 1MA67
Rohde & Schwarz recognizes the potential risk of computer virus infection when con-necting Windows®-based test instrumenta-tion to other computers via local area net-works (LANs), or using removable storage devices.This white paper introduces measures to minimize malware threats and discusses ways to mitigate risks while insuring that instrument performance is not compro-mised.The paper discusses the use of anti-virus software. It also outlines how to keep the Windows® 7 operating system properly updated through regular installation of OS patches.
27-Jan-2015 | AN-No. 1DC01
O-RAN makes radio access networks more open, disaggregated and flexible. O-RUs need to comply with 3GPP and O-RAN standards. Automation is crucial for extensive O-RAN conformance testing since O-RAN network elements are asynchronously released.
08-May-2024
conducted conformance testing according to TS 38.141-1, Rel. 16
3GPP defines the Radio Frequency (RF) conformance test methods and requirements for 5G NR Base Stations (BS) in the technical specifications TS 38.141. This application note describes how all mandatory RF transmitter tests (TS 38.141-1, chapter 6), according to Release 16, can be performed quickly and conveniently with signal or spectrum analyzers from Rohde & Schwarz by either choosing manual operation or a remote control approach. Moreover, some test cases require additional signal generation equipment from Rohde & Schwarz.In Addition, a new Python software library comes with this application note to enable the remote control approach of base station testing. This example requires the RsInstrument module which can be found on pypi.org or installed via 'pip' and is provided as is.
27-Jan-2021 | AN-No. GFM313
This Application Note gives 10 useful Tips & Tricks for the users of Rohde & Schwarz attribute-based instrument drivers. It is recommended for the first-time LabVIEW users as well as for the experienced programmers.
30-Jan-2017 | AN-No. 1MA228
radiated conformance testing according to TS 38.141-2, Rel. 16
3GPP defines the Radio Frequency (RF) conformance test methods and requirements for 5G NR Base Stations (BS) in the technical specifications TS 38.141. This application note describes all mandatory RF receiver tests (TS 38.141-2, chapter 7), according to Release 16.Furthermore, this document provides a brief introduction about the different R&S OTA antenna test solutions and how they are applicable for base station conformance testing. Rohde & Schwarz offers suitable solutions for any test case that is mentioned in this application note.
30-Jun-2020 | AN-No. GFM325
The Bluetooth® wireless standard has been an unparalleled success. It has found its way into virtually all smartphones, PCs, cars, entertainment hardware and wearables. Bluetooth SIG reports that more than 8 billion devices are currently in use. Bluetooth supports Internet of Things (IoT) technologies and direction finding methods, making it a sure bet for the future as well.This white paper summarizes the various Bluetooth technologies with a focus on the physical layer in line with core specification version 5.1.
05-Jun-2019 | AN-No. 1MA108
Starting from June 2017, almost all radio transmitters and receivers sold or put into operation in the European Union have to be tested for immunity against interferers in adjacent frequency bands. ETSI standard EN 303 340 defines the tests to be performed on digital television receivers and requirements to be passed.This application note describes the test procedures and provides save-recall files and interferer signals for the Broadcast Test Center R&S®BTC.
11-Jul-2017 | AN-No. 1GP116
More and more everyday items such as household appliances, vehicles, lights, etc. are now connected to the Internet, forming what is known as the "Internet of Things". Even clothing with sewn-in sensors to measure vital functions can now connect to the Internet and transmit data to cloud services. These different things use a variety of wireless technology standards to establish a connection. Due to its popularity, one of the most important standards is Bluetooth (or Bluetooth Low Energy). Before a new product with Bluetooth functionality can be launched, the qualification process defined by the Bluetooth SIG must be successfully completed. To save time and money, performance tests need to be performed in the development stage. This application note describes how to use the R&S CMW platform to perform the measurements defined in Bluetooth test specification version 5. As an alternative solution, we also cover how to perform almost all of the measurements with a spectrum analyzer and signal generator.The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Rohde & Schwarz is under license.
19-Jun-2017 | AN-No. 1MA282
Rapid and accurate verification of beamforming weights is required for example, for codebook generation or beamforming algorithm development or verification. This document describes the unique application of Rohde & Schwarz VNA (Vector Network Analyzers) to fully characterize the passive part of multi-element antennas intended for beamforming.A range of R&S VNA models are optionally equipped with multiple independent sources, whose relative amplitude and phase may be arbitrarily controlled ("defined coherence mode"), in addition to frequency and true time delay. These sources may be connected to individual elements of a multi-element antenna to derive and verify transmit (Tx) mode beamsteering and beamforming operation.The R&S®ZVA in "Defined Coherence Mode" can electronically be switched to / from the conventional S-parameter mode. Therefore, Sparameter and beamforming measurements may be performed efficiently within a single connection cycle of the antenna.Multiple VNA may be daisy-chained, to extend the concept shown to support an arbitrary number of ports.The R&S®Quickstep sequencing software may be downloaded from:https://www.rohde-schwarz.com/software/quickstep/
20-Mar-2017 | AN-No. 1MA278