783 Results
How to see the graphic of a modulated signal to be downloaded to the signal generator SMBV100A, SMBV1000B, SMW200 with the WINIQSIM2.
During the call setup with VoLTE/VoWiFi with EVS voice codec the bandwidth is negotiated. How can the bandwidth be setup and how will it be shown in the CMW user interface?
I need to activate the deembedding function on a specific port. The data is available on a touchstone file (s2p) How can I load the file with remote commands?
I am using R&S ELEKTRA with EMI Receiver for conducted measurements with a LISN. During installation and first measurement, we had the "IFOVLD" error, what does mean results are invalid.
We have installed our test system with EMC32 and all devices, but NRP2 can not be set to physical from EMC32 using LAN interface.
For radiated emissions test I would like to change the antenna factors to another antenna. Would it be possible to get a step by step guide as to how to create a new radiated emissions test using my EMI Test Receiver receiver with a new antenna?
How can I switch from remote to local state via remote control?
I want to use the "Remote Display" function of the Instrument View software. Instead of the screen I just see a "white" area. My PC is connected via USB. How can I use it?
I want to connect my HE400 to my handheld devices. Unfortunately I don't know which adaptor cable I need for that task. Is there an overview available?
I tried to measure the Voltage Noise of my power supply unit which is specified to the following values. My results have been much higher and I sent in the device for alignment/calibration. After getting it back I still gather the same results. Can you explain how to perform such a measurement?
Is it possible to have multiple access to the HMP series PSUs via TCP/IP? I want to control the device from two different applications and keep the connections open all the time.
I want to expand the output power of my PSU using some channels in parallel. How can I use sensing in that case?
If a CMWrun test plan script has been fished the AC power of a CMW500 / CMW290 / CMW270 should be shut down automaticly.
I would like to connect a controller with EMC32 program and measure the disturbance field strength with at a certain distance in sync with motorised rail. I would like to setup the communication between my controller and EMC32. Can you send me some instructions for communication between EMC32 and external hardware?
I followed steps to determine an IP address to my NRP series sensor. Unfortunately without no success as I can not find the sensor at all.
Some parts of my program cause timeouts. Is it possible to track the traffic via my VISA installation? It would help me a lot to see the complete command flow including timing information
I am using the I/O Logging function to write all remote commands sent to the ZNL(E) to file. But I can not find any logging file in the path mentioned in the manual: C:\ProgramData\Rohde-Schwarz\ZNL-FPL\ScpiLogging
I would like to be sure about the high impedance state of a dedicated channel for my power supply unit. Do you have a process to test and to ensure that? Can you also please explain, how the high impedance mode works?
How do I calculate these frequency points when I have a logarithmic sweep and know the center frequency, the span and the number of sweep points?
I created an arbitrary waveform using a remote control program. I am struggling to find the according SCPI command to trigger the sequence. At the moment I can only trigger it manually using the button on the device. Is there a way to do this completely by remote control?
I have used my TRL calibration kit with my ZVA before. Now I want to use also with my ZNB. But when I try to load the data of the calibration kit into the ZNB, the above error message is shown.
Sense protection request on NGx series PSU during remote control
I use the HMF2550 as a Sinus generator in combination with AM modulation. The power level of my modulated signal is too low. If I switch off modulation (pure CW) the signal level is fine again. What's the background of this behavior?
When starting MOS audio quality measurments with CMWRun connected to a CMW communication tester and an UPV audio analyzer, a failure message occurs that the calibration files "mobile_in.ccl" and "mobile_out.ccl" can not be found.
I use my CMA180 to gauge several tones sent by my transceiver. Unfortunately I can see these tones in the dialing section (they will be detected) and in the scope. However, I can not see the desired additional information in the OverView or AF Results tab: Are there some settings I have overseen?
When I query the waveform with "CHANx:DATA?" the resolution is just that what is displayed on the screen. But I have manually changed the record length to achieve a high resolution. How do I get the data of the waveform with full resolution?
We are performing EMS Tests and we need live data of frequency and level. The two values are to be read out from EMC32 and transferred to Vector CANoe, the intention is to synchronize with the corresponding values for frequency and level. Are there any ready to use tools available, to read the required data from EMC32?
I want to use the LCX series LCR Meter to automatically control and sort components. One of the tasks is to differentiate between the following three values of resistors: - Less than 990 Ohm, - Middle range from 990 to 1010 Ohm (1 kOhm), - More than 1010 Ohm. How can I set this measurement up and which pins do I have to use at the 15 PIN SUB-D socket at the rear side of the LCX?
I would like to do a Reference Calibration using ELEKTRA and Field Probe. For this I have to do Reference Calibrations at 16 positions, this does mean my Field Probe have to be set to each of the 16 predefined points. I set the probe positions manually, so an error can occur by mistake. Is it possible to repeat a measurement for a sensor position, if needed?
I want to export the waveform data of my RTO scope into MATLAB, but the only way I found so far is the screenshot option. Is there another way to use the trace data in my script?