Webinars and videos on future automotive mobility

Application video: Measuring with the R&S®QAR50

Learn more about the QAR50's measurement capabilities and unique features within this 5 minute video.

CAN bus trigger and decode using the R&S®MXO4 oscilloscope

Watch this video to get a practical demonstration of how to use the MXO4 oscilloscope’s CAN bus trigger and decode capability to debug CAN interfaces and busses.

Explainer video: How Full-Vehicle OTA Antenna Testing ensures infotainment Quality of Service

Infotainment Quality of Service is a competitive differentiator for vehicle manufacturers. However, the delivery of digital services to vehicles relies on robust wireless connectivity, and a critical element in the communication chain are the vehicle antennas. Watch this video to how learn OTA testing in a controlled environment can verify the antenna performance and ensure infotainment Quality of Service.

Trigger on Zones in real-time. RTP - see the difference

The RTP's Zone trigger allowes as the only oscilloscope in the world to isolate events in the time and the frequency domain.

Application video: Accelerating ADAS-AD with Hardware-in-the-Loop Testing

High-Precision In-Band Radar Test Solution

Check out R&S high-precision in-band radar testing solutions live from the show floor at CES 2022.

CES: Ultra-Wideband Device Testing

Check out this brief demo on R&S solutions for ultra-wideband devices. Live from the CES 2022 trade show.

CES: Automotive Radar Object Simulation for Validation

Check out R&S Automotive Radar Object Simulation solutions for validations, live from the show floor at CES 2022.

1000BASE-T1 automotive Ethernet compliance test with Test Mode 4

Performing the “Distortion with disturber” test on a 1000BASE-T1 DUT from Marvell.

Application video: Automotive radar object simulation with the AREG800A and QAT100

Watch the output of our radar test system in different use cases. This video shows the RTS in stand-alone operation, remote control and a basic HiL setup.

Hardware-in-the-loop validation for automotive radar

Rohde & Schwarz and Vector Informatik will showcase a combined solution for reliable and reproducible over the air, closed loop testing of todays and tomorrows ADAS/AD features.

Automotive Multigigabit

In this video we use the R&S VNA ZNB20 together with TE connectivity BEAMnet miniaturized multi-gigabit connector system. The tests are according to the OPEN Alliance TC9 draft specification for 2.5/5/10GBASE-T1 Watch now

1000BASE-T1 interoperability test

In this video we show how to perform the Signal Quality Indicator (SQI) test requirement for the OPEN Alliance TC12 Interoperability test with 1000BASE-T1.

gPTP (IEEE 802.1AS) Validation Test

In this video we validate gPTP with an R&S RTO6 oscilloscope to measure and compare 1pps signals according to IEEE 802.1AS

Test certification experts IB-Lenhardt & Rohde & Schwarz

Automotive radar sensors are used in complex and safety-critical applications such as advanced driver-assistance systems (ADAS). Therefore, their correct function and compliance with relevant regulations, must be verified. Watch this short video to find out how IB-Lenhardt conduct this important service with the help of Rohde & Schwarz.

Verify device functional KPIs in lab using field data

Reduce time and cost by verifying important device KPIs in lab under realistic network conditions using R&S CM360o Field-to-Lab solution for 5G. Replicating field data in lab enriches the testing capability of R&S CMX500 allowing its users to deploy devices with confidence.

CAICT Cellular-V2X (C-V2X) conformance test system

Cellular-V2X (C-V2X) is a key technology which will improve road safety in the coming years. Rohde & Schwarz and Neusoft collaborate to provide a China Academy of Information and Communications Technology (CAICT) Conformance Test system based on the R&S®)CMW500 / R&S®)SMBV100B testers.

Demonstration of C-V2X PC5 Test cases helping to improve road safety

Cellular-V2X (C-V2X) is a key technology which will improve road safety in the coming years. Rohde & Schwarz are introducing a demonstration of our C-V2X RF testing capabilities based on our R&S®CMW500 system against an Industry leading Device.

C-V2X / PC5 in-field coverage and signal quality measurement

The rollout of the C-V2X / PC5 communication interface is an important milestone to ensure safety, convenience and efficient vehicle-to-everything driving data communication. We are sure that this will become mission critical and security relevant in the near future. A research project on in-field C-V2X / PC5 measurements with a network scanner checks the quality and coverage of the PC5 communication channel.

Full vehicle antenna testing

Application video: Get an overview of the topic of OTA Full Vehicle Antenna Testing in this short video and discover how test system design can deliver accurate characterization of an entire vehicle's antennas.

eCall (emergency call)

eCall is a European initiative intended to bring rapid assistance to motorists involved in a collision anywhere in the European Union.

High-End GNSS simulation with the R&S®SMW200A - Episode 6

This video shows how to perform advanced interferer simulations for testing multi-antenna GNSS receivers with anti-jam capabilities, also known as Controlled Reception Pattern Antennas (CRPAs).

High-End GNSS simulation with the R&S®SMW200A - Episode 5

The performance of GNSS receivers must be validated and characterized not only under ideal conditions, but also in the presence of other communication signals like GSM, UTMS or LTE.

High-End GNSS simulation with the R&S®SMW200A - Episode 4

Unintentional or intentional interference can significantly impair the reception of GNSS signals.

Wideband signal analysis in the mmWave range presented at EuMW 2017

Rohde & Schwarz demonstrated 5 GHz signal analysis bandwidth at the European Microwave Week 2017 in Nuremberg.

1000BASE-T1 cable testing according to OPEN Alliance TC9

A guide to perform cable testing based on unshielded twisted pair (UTP) for 1000BASE-T1 based on the OPEN Alliance TC9 specification.

100BASE-T1 compliance testing - MDI return loss

A guide to carrying out a 100BASE-T1 compliance test for the MDI return loss using an R&S®ZND 2-port vector network analyser controlled by the ScopeSuite automation software.

Powerful 100BASE-T1 decoding

Decoding details for 100BASE-T1 Automotive Ethernet using the R&S®RTO with K57 option.

Decoding automotive Ethernet and CAN using R&S scopes

A comparisson between CAN decoding on the R&S®RTM oscilloscope with automotive Ethernet decoding using the K57 option on the R&S®RTO oscilloscope.

Powerful 100BASE-T1 triggering

Triggering details for 100BASE-T1 Automotive Ethernet using the R&S®RTO with K57 option.

1000BASE-T1 compliance testing - Test mode 4: Transmitter distortion test with disturber

A guide to carrying out a 1000BASE-T1 compliance tests with test mode 4 (transmitter distortion test with disturber) on an R&S®RTO. The video gives an overview of how to configure the setup and generate test reports for further analysis.

1000BASE-T1 compliance testing - Test mode 6: Maximum output droop

A guide to carrying out a 1000BASE-T1 compliance tests with test mode 6 (maximum output droop test) on an R&S®RTO. The video gives an overview of how to configure the setup and generate test reports for further analysis

1000BASE-T1 compliance testing - Test mode 2: MDI jitter and clock frequency

A guide to carrying out a 1000BASE-T1 compliance tests with test mode 2 (MDI jitter and clock frequency) on an R&S®RTO. The video gives an overview of how to configure the setup and generate test reports for further analysis.

1000BASE-T1 compliance testing - Test mode 5: Transmitter power spectral density (PSD), power level and peak differential output

A guide to carrying out a 1000BASE-T1 compliance tests with test mode 5 (transmitter power spectral density) on an R&S®RTO. The video gives an overview of how to configure the setup and generate test reports for further analysis.

Radar applications: Radar range and velocity measurements - Video 2/2

In this video we show a powerful way to perform radial velocity and range measurements using Rohde & Schwarz instruments as well as signal processing software implemented in MATLAB.

Radar applications: Radial velocity measurements - Video 1/2

In this first video, we start with a simple application such as distance and speed measurement. The basic setup for radar velocity tests is shown. The theory basics and formulas are explained. The video shows a test using a moving vehicle and how the data is evaluated using an oscilloscope.

EMI debugging

This video shows how the R&S®RTO oscilloscope can be used with a near field probe to find and fix EMI issues quickly and reliably during the development at the R&D lab thereby minimizing expensive re-testing and shortening time to market.

How to perform Bluetooth 5 testing with the R&S®CMW test platform

The video demonstrates Bluetooth 5 measurements using the R&S CMW270 wireless connectivity tester.

Reliable all-in-one test solution for automotive radar sensors

Rohde & Schwarz demonstrated the all-in-one test solution for the production of automotive radar sensors at European Microwave Week 2017 in Nuremberg.

Rohde & Schwarz - your partner in automotive testing

Managing increasingly complex electronic systems and industry standards such as automotive Ethernet create additional requirements for automotive testing, alongside security issues.

Triggering & decoding 100Base-T1 BroadR-Reach Ethernet

Triggering & decoding real-world OABR automotive Ethernet with an oscilloscope.

1000BASE-T1 compliance testing - Test mode 1

Guideline for 1000BASE-T1 compliance testing using the R&S®RTO and R&S®ZND.

100Base-T1 compliance testing

Guideline for 100Base-T1 compliance testing using the R&S®RTO and R&S®ZND.

High-End GNSS simulation with the R&S®SMW200A - Episode 3

In this third video of R&S’s new video series on high-end GNSS testing, it is shown how to set up a multi-constellation, multi-frequency GNSS scenario and feed the GNSS signals to a connected GNSS receiver.

High-End GNSS simulation with the R&S®SMW200A - Introduction

This video introduces a new series of videos covering the new R&S®SMW200A GNSS simulator. A general discussion of today’s GNSS testing needs is followed by an overview of key features and possible GNSS configurations for the R&S®SMW200A.

High-End GNSS simulation with the R&S®SMW200A - Episode 2

In this second video of R&S’s new video series on high-end GNSS testing, it is shown how to work with the instrument, followed by a quick user interface tour introducing the most important configuration options and simulation monitoring features.

Field-to-lab testing of cellular devices presented at GSMA MWC 2018

Rohde & Schwarz presented tools to reduce expensive and time-consuming drive tests for LTE, NB-IoT and eMTC devices at the GSMA Mobile World Congress 2018 in Barcelona.

First cellular V2X signaling solution for 3GPP Rel.14 presented at GSMA MWC 2018

Rohde & Schwarz presented a protocol and application test solution for cellular V2X (C-V2X) at the GSMA Mobile World Congress 2018 in Barcelona.

Test solution for NGeCall modules presented at GSMA MWC 2018

Rohde & Schwarz demonstrated a test solution for Next Generation eCall (NGeCall) modules at the GSMA Mobile World Congress 2018 in Barcelona.