235 Results
This application note discusses WLAN standard IEEE 802.11n. It first describes the most important amendments to previous releases and the ambitious new measurement tasks.
26-Apr-2013 | AN-No. 1MA179
UMTS Long Term Evolution (LTE) Technology Introduction
14-Sep-2009 | AN-No. 1MA111
This paper will provide an overview of the current status of the ITS worldwide with a focus on the IEEE 802.11p PHY. Additionally, the paper provides information on test and measurement solutions for devices and components used in ITS.
23-Jan-2014 | AN-No. 1MA152
Rohde & Schwarz Drivers under VEE - Installation and Troubleshooting
20-Dec-2012 | AN-No. 1MA035
The R&S EX-IQ-Box serves as a digital baseband interface between a device under test (DUT) and Rohde & Schwarz generators, analyzers and radio communication testers.
23-May-2012 | AN-No. 1MA168
This application note describes in detail the steps required to make a noise figure measurement on a spectrum analyzer using the “Y Factor” technique. Background equations are presented for each step of the calculation.
25-Jul-2012 | AN-No. 1MA178
Key parameters such as EVM and the AM-AM curve are measured and the compensating effect of digital predistortion is shown. amplifier, AM-AM, AM-PM, saturation, non-linearity, digital predistortion, FSV3-K18 This video shows how to measure the distortions caused by an amplifier under test.
This document provides an introduction to SDR as used for military radios and presents the relevant T&M solutions offered by Rohde & Schwarz.
15-Sep-2012 | AN-No. 1MA206
The R&S®FS-SNS smart noise sources simplify measurements and uncertainty calculation by automatically uploading the required correction tables and environmental temperature to the spectrum analyzer. video, spectrum analyzer, amplifier, noise figure, gain, y-factor method, FSV3-K30 This video shows how to measure the noise figure and gain measurements of an amplifier under test using a noise source.
Compared to the R&S®FSV analyzer, the R&S®FSVA offers lower phase noise, higher sensitivity and 160 MHz analysis bandwidth up to 40 GHz.
The first part of this educational note presents the applications for and the most important types of signal generators. This is followed by a description of the construction and functioning of analog and vector signal generators.
03-May-2016 | AN-No. 1MA225
R&S®Forum for Instrument Remote Control
28-Jun-2018 | AN-No. 1MA196
Versatile Software Tool for Rohde & Schwarz Instruments
RSCommander is a versatile software tool for a wide range of Rohde & Schwarz spectrum-, network analyzers, signal generators and oscilloscopes. It allows for automatic instrument discovery, making screenshots, reading traces, file transfer and simple script creation.
24-Dec-2017 | AN-No. 1MA074
R&S®VISA is a standardized software library that allows fast communications over diverse interfaces with a wide variety of T&M instruments that are detected on the network from PC applications.
26-May-2020 | AN-No. 1DC02
Testing the world’s first quantum error correction stack
How Kyrio found its perfect O-RAN conformance T&M solution from Rohde & Schwarz and VIAVI Solutions.
R&S FSx-K18x Amplifier Measurements - Specifications
Rohde & Schwarz signal and spectrum analyzers accurately measure the noise figure in the millimeterwave frequency range using the Y-factor method.
17-Jul-2017
Wide range of set-top box tests in line with current DVB-xx standards using a variable, future-ready test system
13-Jul-2012
R&S Fxx-K30 Measure noise figure above 110GHz - Application Card
Software tool for fast and repeatable optimization of signal analyzer RF front-end settings
The signal conditioning in the RF front-end of signal analyzers is crucial to achieve the best performance with respect to image-suppression, noise-floor, dynamic range and other RF-key parameters.Precise signal levelling is especially important for complex measurements like Error-Vector-Magnitude (EVM). To minimize the measurement uncertainty from test system contributions over a wide range of different levels, the RF front-end needs to be adapted continuously according to the signal characteristics, signal power and frequency - ideally using an automatic levelling algorithm.This document describes the approach of a waveform specific, on-site characterization of the signal analyzer: For each waveform and frequency of interest, the instrument is evaluated in a first step. With this additional data, a fast and repeatable auto-levelling can be performed during the actual measurement.
24-Jan-2022 | AN-No. 1EF111
R&S VSE-K10/FSx-K10 GSM Measurements - Specifications
Active, high-impedance probes can be connected to spectrum analyzers, providing a practical and highly precise measurement solution to overcome an otherwise cumbersome RF testing issue. This application note provides information on how to use oscilloscope probes in RF measurements using spectrum analyzers
04-Jul-2023 | AN-No. 1EF116
Carrier aggregation — (one) key enabler for LTE-Advanced -
This application note explains how to convert different Rohde&Schwarz I/Q file formats among each other using the supplied software tool.
23-Sep-2015 | AN-No. 1EF85
Rohde&Schwarz presents a customizable solution for testing GNSS receivers to ensure a certain resilience against (legal) interference from neighboring bands.
18-Jul-2017
In order to make it easier to monitor the use and status of instruments, some devices offer the software option Health and Utilization Monitoring Service (HUMS). HUMS provides all necessary information about the health status and utilization over time in many details.
11-Jan-2021 | AN-No. GFM336
This application note gives a short introduction to NB-IoT (Internet of things) and shows the easy measurements with Rohde & Schwarz instruments like transmitters and test receivers.
30-Jun-2017 | AN-No. 1MA296
This Application Note gives a short overview how signals with two different modulation schemes can be analyzed using the R&S®FSW.
18-Apr-2016 | AN-No. 1EF93
R&S VSE-K106/FSx-K106/FPS-K106 EUTRA/LTE NB-IoT Measurement Application - Specifications