Search Application Notes & Cards
Learn how to configure Rohde & Schwarz products to fit your application. Search our database by product, technology, or application to find relevant technical documents.
Search Application Notes & Cards
Learn how to configure Rohde & Schwarz products to fit your application. Search our database by product, technology, or application to find relevant technical documents.
1110 Results
The power efficiency of the drive electronics is a key parameter when developing electric drive systems. The conduction loss of the electric drive electronics is of special interest. One important parameter for determining the conduction loss is the RDS(on) of the MOSFET. When a switching MOSFET is off, it has a high drain-to-source voltage, but when it is turned on, the voltage drops to just a few hundred millivolts. A highresolution oscilloscope is needed to measure these low voltages. Probe compensation and correct probing are also vital for accurate RDS(on) measurements.
19-Mar-2015
A new phase noise test instrument covers the frequency range from 1 MHz to 50 GHz with direct down-conversion analog I/Q mixers and baseband signal sampling. The traditional PLL has been replaced by a digital FM demodulator for phase detection and frequency tracking. An additional AM demodulator enables concurrent measurement of phase and amplitude noise. The instrument can measure phase noise as low as -183 dBc/Hz with a 100 MHz carrier frequency and 10 kHz offset within two minutes.
09-May-2016
The R&S®SMW200A together with the R&S®FSW is a state of the art testing solution that significantly reduces the required hardware for testing power amplifiers with envelope tracking and/or digital pre-distortion. This application note introduces the test solution in detail and presents corresponding measurement examples.
25-Sep-2014 | AN-No. 1GP104
Reflection measurements are a common way of assessing antenna system performance. When a minimum amount of the transmitted signal is reflected, it indicates that the transmission energy can reach the intended coverage. Undesired high reflection causes the system to be inefficient and can damage components. Reflection measurements can be expressed in terms of return loss, VSWR and reflection coefficient.
13-Nov-2017
Connecting simulation and measurements on physical devices
This application note is based on collaborative work between MathWorks® and Rohde & Schwarz. The focus is on linearization of a non-linear device, in our case the RF power amplifier. It is shown how simulation and the integrated functions of the Rohde & Schwarz instruments R&S®SMW200A and R&S®FSW work hand-in-hand with the simulation capabilities from MathWorks in MATLAB / Simulink. The goal is to provide a toolset to enable proper modeling and linearization approaches to optimize and verify the behavior of the power amplifier when used with complex wideband signals as used in 5G NR or latest satellite links.The application note brings code examples and an exemplary block set for MATLAB / Simulink to provide an easy start to replicate and use the described procedure.
05-Aug-2021 | AN-No. 1SL371
An offline AC/DC switching converter has no separate bias power supply that provides power to the control integrated circuit itself. Here, an auxiliary primary winding and discrete components are added to supply power to the control circuit. Verifying this circuitry is essential and requires accurate and detailed signal level and timing measurements. The startup sequence takes a long time, which needs to be taken into consideration in the measurement and requires an instrument with sufficient memory.
23-Nov-2022
This White Paper describes the implementation of real-time capabilities within the R&S®FSW (with option K160R) and the R&S®FSVR. It shows fields of application as well as the technical implementation.
20-Mar-2015 | AN-No. 1EF77
Calibration and Verification Solution
The UWB (Ultra-Wideband) technology is a short range wide-band radio technology specified for device to device communication operating in unlicensed spectrum. It is an RF positioning technology that enables accurate and secure peer-to-peer ranging between mobile devices with robust resistance to interference while consuming very low energy and coexisting well with other radio communication systems. UWB is used for a variety of different applications, such as asset tracking, secure payment, personal tracker, real time location services and keyless access and start of a vehicle etc. According to ABI Research forecasts, there will be well over 1 billion UWB annual device shipments by 2026. Almost every smart phone shipped in 2026 will support UWB services.Talking about testing aspect of a UWB device, in general two test methodologies can be adopted as other wireless products, either the traditional testing mode (so-called conducted test mode) with wired RF connection between the test measurement equipment and device under test (DUT) or over the air (OTA) test mode in an OTA anechoic chamber. Sometimes, it is not always possible or necessary to perform the tests under conducted mode due to the limiting factors, e.g. cost, space, complexity and direct access to the RF connectors of the product. In this case, OTA testing is then becoming a non-evitable approach. Moreover, OTA testing reflects the usage of DUT in a real condition.In this application note, R&S® OTA test solution covering transmitter (Tx), receiver (Rx) and Time of Flight (ToF) testing in Wireless Automated Testing (WMT) environment is described. The measurement results throughout the whole document are based on NXP Trimension™ NCJ29D5 UWB automotive IC.
12-Apr-2023 | AN-No. 1SL394
The IP connection security analysis solution for the R&S®CMW500 platform identifies IP connection vulnerabilities in telematics units at an early stage of development.
18-Jul-2017
Welcome to our short video tutorials on how to test radars using Rohde & Schwarz test equipment. Access to most information about radar is pretty restricted, as many radar applications are military or secretive industrial research. To show you some basic Radar tests we have created RADAR demo tools, which functions at a frequency of 2.45 GHz, which is in the unlicensed 2.4 GHz Industrial, Scientific and Medical band. So we can even perform our tests in unshielded rooms. The frequencies are also used by radar operating in the ITU "S"-band from 2.3 to 2.5 GHz for air traffic control, weather and marine radar. The videos are suitable for 'from-the-scratch' introduction of R&S RADAR test equipment. They can also be used for plain introduction to the RADAR principle.
03-Feb-2014 | AN-No. 1MA209
RF pulse measurements, to characterize the signal in the frequency domain, are traditionally carried out on an RF spectrum analyzer. For time related pulse parameters, oscilloscopes are widely used. However, the measurement capabilities of state of the art test and measurement equipment has evolved over time and crosses domains. With a combination of R&S®RTO digital oscilloscope and dedicated pulse analysis software R&S®VSE-K6, pulse signals can be analyzed in both domains, frequency and time.The R&S®RTO digital oscilloscopes are unique in that they allow output of I/Q data for processing. This application note focusses on signal measurement using this instrument.Analysis of an L-/S-band ATC RADAR utilizing the R&S®RTO2044 oscilloscope running Vector Signal Explorer Software R&S®VSE and Pulse Analysis personality R&S®VSE-K6 is followed by measurements on an X-band RADAR utilizing R&S®FSW, R&S®FPS, R&S®FSV or FSVA signal & spectrum analyzers with the same dedicated R&S®VSE-K6 software.
18-Oct-2016 | AN-No. 1MA249
This White Paper provides a more detailed view on radar waveforms for Aerospace and Defence and commercial radar systems. Waveforms such as pulse and pulse-Doppler signal, continuous wave and frequency shift keying waveforms are described. It also shows continuous waveform trends designed for specific needs and application differences of continuous wave radar compared to pulse radar systems.
31-Aug-2015 | AN-No. 1MA239
Two R&S®ETL TV analyzers or two R&S®ETC compact TV analyzers are used to measure the receive level of a car antenna against that of a reference antenna. The R&S®BCDRIVE broadcast drive test software exports measured data for display in Google Earth.
19-Feb-2015
Integrating the R&S®SMBV100B GNSS simulator into the AVL DRIVINGCUBE™ toolchain creates new possibilities for validating advanced driver assistance systems and autonomous driving functions at the vehicle level. Combining a complete vehicle on a vehicle test bed with physical sensor stimulation results in fast, reproducible and cost-efficient testing. All possible driving scenarios can be executed under realistic and safe conditions.
09-Jan-2020
When it comes to testing analog and digital TV and audio broadcast receivers in cars, special requirements must be met. Although suppliers ensure the receiver functionality, this functionality must be tested when the receiver is integrated into the car. When it comes to testing analog and digital TV and audio broadcast receivers in cars, special requirements must be met. Although suppliers guarantee the receiver functionality, this functionality must be tested when the receiver is integrated into the car.
19-Feb-2015
This application note describes how to detect even small fails in dynamic turn indicators with R&S®AdVISE.
30-Jul-2020 | AN-No. 1S006
Test, calibrate and verify high-performance automotive radar sensors with the R&S®ATS1500C CATR antenna test system and the R&S®AREG100A automotive radar echo generator.
13-Jan-2020
Today’s cars are highly integrated and interconnected. Up to 150 embedded electronic control units (ECUs) in a car secure a convenient and safe driving experience. Examples of ECUs include transmission control modules, ECUs for air conditioning systems, and even self-updating 5G-ready telematics control units.
06-Jul-2020
Power amplifiers in digital TDMA mobile phones are fed with current only during the active slot to save power. Using conventional measuring equipment, the noise figure, an important parameter in power amplifiers, can only be determined with the amplifier in continuous operation. However, continuous operation can lead to amplifier overload and produce distorted results. Now there is a convenient way of determining the noise figure of amplifiers with pulsed power supply: using a Spectrum Analyzer (FSP or FSE or FSIQ or ESI), Noise Measurement Software FS-K3 and a function or pulse generator.
19-Dec-2000 | AN-No. 1MA32
This application note describes the principle of harmonic mixing and the requirements to be met by spectrum analyzers and external mixers.
05-Mar-1999 | AN-No. 1EF43
The ‘Data Reduction’ sequence step is an essential part of an EMI Auto Test since it evaluates the relevant frequencies at which the final measurements are to be done. The intention of this application note is to make the data reduction data flow more transparent (contents of input and output tables) and how the parameters (location and relations) influence the evaluation algorithm.
16-Nov-2011 | AN-No. 1SP02
The Application Note summarises all measurements for WLAN test, according to the IEEE Standards 802.11a, b and g. For each measurement, an instrument list, test setups, test method, comments, typical results and implementation hints are included. The enclosed free of charge software provides all IEEE 488 bus sequences ready to run or copy into your own test environment.
28-Jul-2004 | AN-No. 1MA69
Most of the tests specified in standard TS 34.121 for 3GPP Rel-99 can be performed with R&S®CMW500. This document provides a step by step guide on how to perform Rel-99 measurements on transmitter/receiver characteristics, and performance tests according to TS 34.121 V9.5.0 clauses 5 and 6 with standalone R&S®CMW500. A set of *.sav files based on R&SCMW500 firmware V2.1.20 for UE supporting band I with power class 3 in RMC 12.2 kbps downlink/uplink is attached to this application note.
16-Dec-2011 | AN-No. 1CM95
Near Field Communication (NFC) is a new short-range, standards-based wireless connectivity technology, that uses magnetic field induction to enable communication between electronic devices in close proximity. Based on RFID technology, NFC provides a medium for the identification protocols that validate secure data transfer. NFC enables users to perform intuitive, safe, contactless transactions, access digital content and connect electronic devices simply by touching or bringing devices into close proximity. This White Paper gives an overview of NFC uses, NFC technology and signals and RF measurements on NFC units. NFC analog measurements with R&S test instruments are described in detail in R&S application Note 1MA190 'Basic Tests of NFC Enabled Devices Using R&S Test Equipment'
03-Jun-2013 | AN-No. 1MA182
Combining the R&S®UPP audio analyzers with the R&S®SMB100A signal generators provides the most compact and fastest test solution for modern FM car radios
19-Feb-2015
Development of modern EW systems is a complex and expensive process, that requires thorough testing against all requirements during all phases of development. To keep cost under control, system level testing in the lab is key and brings several advantages: test cases can be reproduced under the exact same conditions as often as necessary. System level testing in the lab is often performed in a hardware-in-the-loop (HIL) environment. This application note provides some insight into generating radar signals for hardware-in-the-loop testing with the R&S®SMW200A. An introduction to HIL testing and realtime operation of the R&S®SMW200A is given. The hardware and software interface, the PDW format and synchronization and timing mechanisms are described. Additionally, various example scenarios and detailed information about intermediate calculations are provided. The application note also provides information about system requirements for advanced PDW streaming with multiple emitters on multiple parallel streams.
22-Jan-2021 | AN-No. 1GP124
The audio performance measurement solution for the R&S®CMW500 platform identifies audio and speech performance issues over a wireless connection.
26-Aug-2017
The effective number of bits (ENOB) is a way of quantifying the quality of an analog to digital conversion. A higher ENOB means that voltage levels recorded in an analog to digital conversion are more accurate. In an oscilloscope the ENOB is not just determined by the quality of the analog to digital converter but by the instrument as a whole. This application note explains how to measure the oscilloscope ENOB and shows results for the R&S®RTO for different settings.
13-May-2011 | AN-No. 1ER03
The R&S®FSW signal and spectrum analyzer with the R&S®FSW-K160R realtime option and the R&S®FSW-K6 pulse measurement option is ideal for testing modern radars.
04-Jul-2013