Search Application Notes & Cards
Learn how to configure Rohde & Schwarz products to fit your application. Search our database by product, technology, or application to find relevant technical documents.
Search Application Notes & Cards
Learn how to configure Rohde & Schwarz products to fit your application. Search our database by product, technology, or application to find relevant technical documents.
1109 Results
The R&S®CMW wideband radio communication tester platform (R&S®CMW500, R&S®CMW270) uses high accuracy distance measurements (HADM) with phase based ranging (PBR) for a comprehensive and fully automated test solution to verify Bluetooth® Low Energy physical layer functionality
06-Sep-2023
Calibration and Verification Solution
The UWB (Ultra-Wideband) technology is a short range wide-band radio technology specified for device to device communication operating in unlicensed spectrum. It is an RF positioning technology that enables accurate and secure peer-to-peer ranging between mobile devices with robust resistance to interference while consuming very low energy and coexisting well with other radio communication systems. UWB is used for a variety of different applications, such as asset tracking, secure payment, personal tracker, real time location services and keyless access and start of a vehicle etc. According to ABI Research forecasts, there will be well over 1 billion UWB annual device shipments by 2026. Almost every smart phone shipped in 2026 will support UWB services.Talking about testing aspect of a UWB device, in general two test methodologies can be adopted as other wireless products, either the traditional testing mode (so-called conducted test mode) with wired RF connection between the test measurement equipment and device under test (DUT) or over the air (OTA) test mode in an OTA anechoic chamber. Sometimes, it is not always possible or necessary to perform the tests under conducted mode due to the limiting factors, e.g. cost, space, complexity and direct access to the RF connectors of the product. In this case, OTA testing is then becoming a non-evitable approach. Moreover, OTA testing reflects the usage of DUT in a real condition.In this application note, R&S® OTA test solution covering transmitter (Tx), receiver (Rx) and Time of Flight (ToF) testing in Wireless Automated Testing (WMT) environment is described. The measurement results throughout the whole document are based on NXP Trimension™ NCJ29D5 UWB automotive IC.
12-Apr-2023 | AN-No. 1SL394
This application note helps to understand the measurement uncertainty calculation for a modern spectrum analyzer and provides a tool to calculate the total measurement uncertainty for different measurements.
21-Apr-2010 | AN-No. 1EF63
This application note shows how to perform Bluetooth transmitter measurements with the CMU200 in a reduced signaling mode, in which the protocol handshake between the Bluetooth Equipment Under Test, the EUT, and CMU200 is skipped. This additional CMU200 feature allows both more flexible and faster RF testing of Bluetooth modules. A step-by-step example with SMIQ demonstrates the principles and serves as a reference for integrating this method in user-specific test strategies.
04-Feb-2003 | AN-No. 1MA49
The IP connection security analysis solution for the R&S®CMW500 platform identifies IP connection vulnerabilities in telematics units at an early stage of development.
18-Jul-2017
Welcome to our short video tutorials on how to test radars using Rohde & Schwarz test equipment. Access to most information about radar is pretty restricted, as many radar applications are military or secretive industrial research. To show you some basic Radar tests we have created RADAR demo tools, which functions at a frequency of 2.45 GHz, which is in the unlicensed 2.4 GHz Industrial, Scientific and Medical band. So we can even perform our tests in unshielded rooms. The frequencies are also used by radar operating in the ITU "S"-band from 2.3 to 2.5 GHz for air traffic control, weather and marine radar. The videos are suitable for 'from-the-scratch' introduction of R&S RADAR test equipment. They can also be used for plain introduction to the RADAR principle.
03-Feb-2014 | AN-No. 1MA209
RF pulse measurements, to characterize the signal in the frequency domain, are traditionally carried out on an RF spectrum analyzer. For time related pulse parameters, oscilloscopes are widely used. However, the measurement capabilities of state of the art test and measurement equipment has evolved over time and crosses domains. With a combination of R&S®RTO digital oscilloscope and dedicated pulse analysis software R&S®VSE-K6, pulse signals can be analyzed in both domains, frequency and time.The R&S®RTO digital oscilloscopes are unique in that they allow output of I/Q data for processing. This application note focusses on signal measurement using this instrument.Analysis of an L-/S-band ATC RADAR utilizing the R&S®RTO2044 oscilloscope running Vector Signal Explorer Software R&S®VSE and Pulse Analysis personality R&S®VSE-K6 is followed by measurements on an X-band RADAR utilizing R&S®FSW, R&S®FPS, R&S®FSV or FSVA signal & spectrum analyzers with the same dedicated R&S®VSE-K6 software.
18-Oct-2016 | AN-No. 1MA249
This White Paper provides a more detailed view on radar waveforms for Aerospace and Defence and commercial radar systems. Waveforms such as pulse and pulse-Doppler signal, continuous wave and frequency shift keying waveforms are described. It also shows continuous waveform trends designed for specific needs and application differences of continuous wave radar compared to pulse radar systems.
31-Aug-2015 | AN-No. 1MA239
Two R&S®ETL TV analyzers or two R&S®ETC compact TV analyzers are used to measure the receive level of a car antenna against that of a reference antenna. The R&S®BCDRIVE broadcast drive test software exports measured data for display in Google Earth.
19-Feb-2015
Current Radar development is focusing the area of signal processing. This is taken into account by this educational note, where the R&S®SMW / SMBV instruments on the transmitter side and R&S®FSW / FSV instruments on the receiver side are combined to a closed loop Radar system, performing radar detection by means of pulse compression and digital signal processing. Appropriate Rohde & Schwarz sofware tools for such applications are described as well as the interface between the tools and the test instruments. Target reader group are engineering students who want to perform tests using pulsed or chirped signals.
20-Nov-2014 | AN-No. 1MA234
The R&S®FSW offers a variety of different bandwidth options and makes it possible to combine these with external harmonic mixers to enlarge the analyzer’s frequency range up to 325 GHz. This application card will give some guidance as to the possible combinations of bandwidth options and mixers in conjunction with the needed IF frequencies.
16-Jun-2020
Verification of the spectrum allocation and in depth analysis of the transmitted signals is very important in many domains. For example, the IEEE 802.11ad standard makes use of approximately 2 GHz bandwidth in the 60 GHz frequency domain. Researchers and developers of Automotive radar discuss the 79 GHz frequency band with an available bandwidth of up to 4 GHz. Finally the upcoming 5G technology for cellular networks discusses the use of up to 2GHz signals in the cm and mm-wave frequency bands.This technical evolution already indicates the need of signal measurement and analysis in the mm-wave domain with high bandwidth.Therefore, this application note presents a method to measure and analyze signals with an instantaneous bandwidth of up to 2 GHz using new tools on the R&S®FSW Signal and Spectrum Analyzer platform in collaboration with an R&S®RTO Digital Oscilloscope.
16-Jun-2015 | AN-No. 1EF92
Integrating the R&S®SMBV100B GNSS simulator into the AVL DRIVINGCUBE™ toolchain creates new possibilities for validating advanced driver assistance systems and autonomous driving functions at the vehicle level. Combining a complete vehicle on a vehicle test bed with physical sensor stimulation results in fast, reproducible and cost-efficient testing. All possible driving scenarios can be executed under realistic and safe conditions.
09-Jan-2020
This document describes the direct test mode mechanisms for testing Bluetooth Low Energy devices and explains how the direct test mode connection is established. The R&S CMW uses a USB port for the direct test mode connection while the Equipment under Test (EUT) may provide a USB port, a serial port or even a 2-wire UART interface for this purpose. Installing or assigning the right driver for the EUT is the main configuration task on the R&S CMW. For EUTs with USB port, the R&S CMW provides a Bluetooth Low Energy USB driver which has to be assigned to the connected EUT.
14-Dec-2016 | AN-No. 1C105
When it comes to testing analog and digital TV and audio broadcast receivers in cars, special requirements must be met. Although suppliers ensure the receiver functionality, this functionality must be tested when the receiver is integrated into the car. When it comes to testing analog and digital TV and audio broadcast receivers in cars, special requirements must be met. Although suppliers guarantee the receiver functionality, this functionality must be tested when the receiver is integrated into the car.
19-Feb-2015
This application note describes how to detect even small fails in dynamic turn indicators with R&S®AdVISE.
30-Jul-2020 | AN-No. 1S006
Test, calibrate and verify high-performance automotive radar sensors with the R&S®ATS1500C CATR antenna test system and the R&S®AREG100A automotive radar echo generator.
13-Jan-2020
Today’s cars are highly integrated and interconnected. Up to 150 embedded electronic control units (ECUs) in a car secure a convenient and safe driving experience. Examples of ECUs include transmission control modules, ECUs for air conditioning systems, and even self-updating 5G-ready telematics control units.
06-Jul-2020
Bluetooth Low Energy (BLE) 5.1 has introduced Angle of Arrival (AoA) and Angle of Departure (AoD) to enrich the direction finding (DF) feature. This application note gives the guidance of how to perform the BLE 5.1 DF RF tests according to the RF test specification of BT 5.1 by using the Rohde & Schwarz test solutions.
30-Oct-2019 | AN-No. GFM327
The R&S®CMW Wideband Radio Communication Tester offers an elaborate parametric test concept, including all RF test cases up to Bluetooth®5, that makes this flexible test platform ideal for designing and verifying Bluetooth® Low Energy (LE) circuitsand modules.
27-Jan-2017
Power amplifiers in digital TDMA mobile phones are fed with current only during the active slot to save power. Using conventional measuring equipment, the noise figure, an important parameter in power amplifiers, can only be determined with the amplifier in continuous operation. However, continuous operation can lead to amplifier overload and produce distorted results. Now there is a convenient way of determining the noise figure of amplifiers with pulsed power supply: using a Spectrum Analyzer (FSP or FSE or FSIQ or ESI), Noise Measurement Software FS-K3 and a function or pulse generator.
19-Dec-2000 | AN-No. 1MA32
This application note describes the principle of harmonic mixing and the requirements to be met by spectrum analyzers and external mixers.
05-Mar-1999 | AN-No. 1EF43
The ‘Data Reduction’ sequence step is an essential part of an EMI Auto Test since it evaluates the relevant frequencies at which the final measurements are to be done. The intention of this application note is to make the data reduction data flow more transparent (contents of input and output tables) and how the parameters (location and relations) influence the evaluation algorithm.
16-Nov-2011 | AN-No. 1SP02
The Application Note summarises all measurements for WLAN test, according to the IEEE Standards 802.11a, b and g. For each measurement, an instrument list, test setups, test method, comments, typical results and implementation hints are included. The enclosed free of charge software provides all IEEE 488 bus sequences ready to run or copy into your own test environment.
28-Jul-2004 | AN-No. 1MA69
The foregoing application note is intended for everyone who desires to become more familiar with the use and upload of custom data in ARB, digital modulation and RF list mode. Particularly, this note describes the instruments R&S® SMW200A, R&S® SGT100A, R&S® SMBV100A, R&S® SMU200A, R&S® SMJ100A and R&S® SMATE200A and provides an overview of already available solutions as well as it gives hints for the writing of own applications. Please also see the application note 1GP88 for the ARB Toolbox software and the application note 1GP96 for the CDM-Toolbox software.
22-Dec-2010 | AN-No. 1GP62
The Rohde & Schwarz Bluetooth RF test solution with the R&S®CMW and R&S®CMWrun is closely aligned to the Bluetooth RF Test Suite. Most of the tests can be performed with the equipment under test connected to a single CMW which is remotely controlled via R&S®CMWrun running on an external computer. Some of the tests require an additional signal generator. This document describes common setups for these tests and the required configurations.
04-May-2015 | AN-No. 1MA261
Most of the tests specified in standard TS 34.121 for 3GPP Rel-99 can be performed with R&S®CMW500. This document provides a step by step guide on how to perform Rel-99 measurements on transmitter/receiver characteristics, and performance tests according to TS 34.121 V9.5.0 clauses 5 and 6 with standalone R&S®CMW500. A set of *.sav files based on R&SCMW500 firmware V2.1.20 for UE supporting band I with power class 3 in RMC 12.2 kbps downlink/uplink is attached to this application note.
16-Dec-2011 | AN-No. 1CM95
More and more everyday items such as household appliances, vehicles, lights, etc. are now connected to the Internet, forming what is known as the "Internet of Things". Even clothing with sewn-in sensors to measure vital functions can now connect to the Internet and transmit data to cloud services. These different things use a variety of wireless technology standards to establish a connection. Due to its popularity, one of the most important standards is Bluetooth (or Bluetooth Low Energy). Before a new product with Bluetooth functionality can be launched, the qualification process defined by the Bluetooth SIG must be successfully completed. To save time and money, performance tests need to be performed in the development stage. This application note describes how to use the R&S CMW platform to perform the measurements defined in Bluetooth test specification version 5. As an alternative solution, we also cover how to perform almost all of the measurements with a spectrum analyzer and signal generator.The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Rohde & Schwarz is under license.
19-Jun-2017 | AN-No. 1MA282
Near Field Communication (NFC) is a new short-range, standards-based wireless connectivity technology, that uses magnetic field induction to enable communication between electronic devices in close proximity. Based on RFID technology, NFC provides a medium for the identification protocols that validate secure data transfer. NFC enables users to perform intuitive, safe, contactless transactions, access digital content and connect electronic devices simply by touching or bringing devices into close proximity. This White Paper gives an overview of NFC uses, NFC technology and signals and RF measurements on NFC units. NFC analog measurements with R&S test instruments are described in detail in R&S application Note 1MA190 'Basic Tests of NFC Enabled Devices Using R&S Test Equipment'
03-Jun-2013 | AN-No. 1MA182
Combining the R&S®UPP audio analyzers with the R&S®SMB100A signal generators provides the most compact and fastest test solution for modern FM car radios
19-Feb-2015