454 Results
Transmitter and Receiver Measurements on Bluetooth Modules with CMU200
06-Aug-2001 | AN-No. 1MA46
Rohde & Schwarz Getting Started for the R&S®EVSF1000 VHF/UHF Nav/Flight analyzer for air navigation and communication signals, with basic information needed to set up and start working with the instrument. Safety information is also included.
Rohde & Schwarz User Manual for the R&S®TSME6 Ultracompact Drive Test Scanner, including the R&S®TSME Device Manager software.
Generation and Measurement of Burst Digital Audio Signals with Audio Analyzer UPD
05-Nov-1997 | AN-No. 1GA38
Advanced Signal Analysis using the History Mode of the R&S RTO Oscilloscope.
03-Jun-2013 | AN-No. 1TD02
This application note describes how noise figure and gain of amplifiers or converters in the microwave range from 50 GHz to 67 GHz are measured.
12-May-2009 | AN-No. 1EF64
Rohde & Schwarz application sheet for the R&S®NRQ6 frequency selective power sensor, describing the power servoing function of an R&S®NRQ6 together with an R&S®SGT100A signal generator
Rohde & Schwarz User Manual for the R&S NRPM OTA power measurement solution, including sensor and antenna modules, and information on how to setup and perform basic measurements and remote command description.
A sinus signal with i.e. 10 V peak-peak, frequency 1 MHz is applied. If I choose a vertical scale which is too small the peaks of the waveform are not displayed as they are out of range. Now I activate the digital filter in the “Vertical” menu à “Channel”. The frequency of the filter is also set to 1 MHz. Now even at very small vertical scales (i.e. 50 mV/div) the waveform is displayed completely, see screenshot. But the amplitude can not be correct. What goes wrong here?
Chipset manufacturers for TV sets, set-top boxes and radios EMC test house engineers TV and radio network operators Car manufacturers and car system integrators (automotive) Infotainment systems manufacturers Car radio chipset manufacturers EMC test houses RED, DAB, R&S®BTC In this webinar we will demonstrate, step by step, how to perform audio measurements on a DAB car radio receiver with the R&S®
Carrier aggregation is the most demanded feature of the LTE-Advanced feature set because it will allow network operators worldwide to aggregate their different spectrum holdings.
Storing and Loading Complete Test Receiver Data Records via IEC/IEEE-Bus
18-Jan-2002 | AN-No. 1EE20
4-Port Measurements with Vector Network Analyzer ZVR
28-Jul-1998 | AN-No. 1EZ25
IEEE 802.16m Technology Introduction
29-Jul-2010 | AN-No. 1MA167
R&S MATLAB<sup>®</sup> Toolkit for R&S<sup>®</sup> NRP-Z Sensors
05-Mar-2011 | AN-No. 1GP61
23-Jan-2024
Rohde & Schwarz to host Demystifying EMC conference as full day webinar in 2024Rohde & Schwarz hosts its popular industry event, Demystifying EMC, on February 6, 2024. The one-day virtual conference kicks off a program of EMC industry expert sessions.
03-Jul-2023
Rohde & Schwarz and MediaTek verify industry's first 3GPP Rel. 17 NTN NB-IoT protocol conformance test casesRohde & Schwarz has partnered with MediaTek to verify the first NTN NB-IoT protocol conformance test cases in line with 3GPP Rel. 17 on MediaTek’s NTN IoT capable MT6825 chipset. This achievement is the next step towards NTN device conformity approval bringing next-generation IoT devices based on non-terrestrial networks (NTN) to the market.
07-Mar-2024
Rohde & Schwarz introduces dedicated phase noise analysis and VCO measurements up to 50 GHz with the R&S FSPN50With the latest model of the R&S FSPN phase noise analyzer and VCO tester, Rohde & Schwarz extends the frequency range for measurements from the previous maximum of 26.5 GHz up to 50 GHz.
23-May-2024
Rohde & Schwarz extends ultra-wideband RF amplifier rangeDesigned for test environments, the BBA300 amplifier offers up to 450 W RF saturation power at the output, at frequencies from 380 MHz to 6 GHz.
The terrestrial television standard DVB T2 is gaining in significance as a result of the growing scarcity of available frequencies. New systems are being tested in many countries around the world. Other countries have already completed the introductory phase for DVB T2. Broadcasting transmitters are subject to particularly stringent standards with respect to broadcast signal quality, because even small faults can lead to service disruptions for many viewers or even disrupt adjacent channels.A single instrument, the R&S®ETL TV analyzer, performs all required DVB-T2 transmitter measurements, from the initial acceptance testing for the transmitter, to measurements performed during commissioning and preventive maintenance.The measurements described here satisfy many country-specific and customer-specific test specifications. Users need only set the limit values accordingly.
23-Jul-2014 | AN-No. 7BM106
WCDMA RF Measurements with the R&S<sup>®</sup>CMW500 according to 3GPP TS 34.121
16-Dec-2011 | AN-No. 1CM95
The R&S®ZNB measures the signal integrity on the PCB, taking the needed test fixtures and probes into consideration – a complete solution in a compact format.
25-Mar-2020
10-Apr-2024
Rohde & Schwarz launches new era of efficient, sustainable, and smart broadcast transmissionThe new R&S®TE1 is industry’s most sustainable transmitter; product debut comes alongside introduction of 24/7 remote monitoring service
16-Dec-2019
RELEASE NOTES: R&S®Web Application Firewall 6.4Last time, we announced the new R&S®Web Application Firewall ‘s management API with a REST/JSON programming interface, allowing automation and scripting of WAF administration tasks, such as management of reverse proxies and tunnels
Measurements on Frequency-Converting DUTs using Vector Network Analyzer ZVR
04-Aug-1998 | AN-No. 1EZ31
This paper will discuss several measurement settings which affect measurement speed and provide suggestions on improving this overall speed.
08-Oct-2020 | AN-No. GFM354
LAN / WAN Connection Of Instruments with Serial Interface By Using a Terminal Server
07-Jul-2003 | AN-No. 7BM41
Operation Guide for HSUPA Test Setup according to 3GPP TS 34.121
07-Oct-2009 | AN-No. 1CM73