Search Application Notes & Cards
Learn how to configure Rohde & Schwarz products to fit your application. Search our database by product, technology, or application to find relevant technical documents.
Search Application Notes & Cards
Learn how to configure Rohde & Schwarz products to fit your application. Search our database by product, technology, or application to find relevant technical documents.
1108 Results
5G networks will need to offer more capacity and flexibility while lowering the operational expenses of the system. Two new technologies can simultaneously address both the increase in capacity and the increase in energy efficiency: Virtualization & Massive MIMO. This white paper provides an overview of test solutions addressing current and future requirements for antenna verification including both conducted and over-the-air (OTA) test methods, which result from applying Massive MIMO antenna technology.This white papers complements the white paper (1MA276) from Rohde & Schwarz, which introduces fundamental theory behind beamforming antennas and provides calculation methods for radiation patterns, a number of simulation results as well as some real world measurement results for small linear arrays.
11-Nov-2016 | AN-No. 1MA286
This application note reviews the measurement uncertainty analysis and traceability for phase noise with the new R&S®FSWP Phase Noise Analyzer.It describes the new approach for measuring phase noise with the R&S®FSWP using direct downconversion with cross correlation and focuses on traceability using a derived primary measurement standard.
05-Jul-2016 | AN-No. 1EF95
This application note and associated application software may be used to conduct psychoacoustic speech quality evaluation for Voice over LTE (VoLTE) connections. The measurements are based on recommendations ITU-T P.862 and ITU-T P.863, respectively.
21-Feb-2014 | AN-No. 1MA204
This Application Note describes testing S-parameters under pulsed conditions with the R&S®ZVA vector network analyzer and either the ZVAX24 Extension unit with pulse modular option or the R&S®SMF signal generator with pulse modulator as a signal source.In addition a constant power level calibration for applications requiring high drive power for test and measurement of device under test (DUT) is also included. A LDMOS S-band radar power transistor is used as example DUT. The pulse profile mode of the R&S®ZVA is used to analyze the time-dependent behavior of the DUT.
11-Apr-2013 | AN-No. 1MA126
Rohde & Schwarz recognizes the potential risk of computer virus infection when connecting Windows®-based test instrumentation to other computers via local area networks (LANs), or using removable storage devices.This white paper introduces measures to minimize malware threats and discusses ways to mitigate risks while ensuring that instrument performance is not compromised.
16-Feb-2017 | AN-No. 1EB01
Due to its outstanding performance the R&S®SMW200A vector signal generator is ideal for testing MIMO receivers in a vast variety of applications offering maximum usability at minimum form factor. It can generate up to eight antenna signals simultaneously in its digital baseband – all standard-compliant and with antenna-specific coding. In addition, it can simulate the complete MIMO transmission channel with up to 32 fading channels, sufficient to emulate higher-order MIMO configurations such as 3x3, 4x4, and 8x4.This application note explains how to use the SMW for testing higher order MIMO systems by presenting different key applications.
24-Feb-2016 | AN-No. 1GP97
Power converter and inverter designs for higher power levels are usually based on hard switching half bridge configurations. In such setups, users must pay particular attention to proper switching operations to prevent shoot-through events. Setting up complex real-time trigger conditions using the R&S®RTE and R&S®RTO oscilloscopes increases the test coverage and robustness of converter and inverter systems.
10-Aug-2020
The ‘Data Reduction’ sequence step is an essential part of an EMI Auto Test since it evaluates the relevant frequencies at which the final measurements are to be done. The intention of this application note is to make the data reduction data flow more transparent (contents of input and output tables) and how the parameters (location and relations) influence the evaluation algorithm.
16-Nov-2011 | AN-No. 1SP02
Application note 1MA25 has been replaced by application note .
28-Aug-2009 | AN-No. 1MA25
This Application Note describes how to perform measurements on power amplifiers for TD-SCDMA base stations to specification TS 25.142 using Rohde & Schwarz generators, power meters and signal/spectrum analyzers. The TD-SCDMA application firmware for Rohde & Schwarz generators and analyzers as well as their outstanding performance facilitate efficient and rapid measurements.
31-Jul-2007 | AN-No. 1MA103
R&S®CMWcards is an intuitive and user-friendly software application that makes NB-IoT OTDOA positioning design verification easier than ever.
26-Nov-2018
The battery life measurement solution for the R&S®CMW500 platform identifies which ECUs and which applications running on telematics units impact battery life.
23-Aug-2017
The Application Note summarises all measurements for WLAN test, according to the IEEE Standards 802.11a, b and g. For each measurement, an instrument list, test setups, test method, comments, typical results and implementation hints are included. The enclosed free of charge software provides all IEEE 488 bus sequences ready to run or copy into your own test environment.
28-Jul-2004 | AN-No. 1MA69
NGE100B, HMC804x, HMP2000, HMP4000, HM8143, NGL200, NGM200, M3SR IN4000A, Power supplies, DC Power supplies, The arbitrary waveform feature o Rohde & Schwarz solutions allow you to simulate device behaviors and replaces basic standalone arbitrary waveform generators. Emulate real-world scenarios with Rohde & Schwarz power supplies NGE100B, HMC804x, HMP2000, HMP4000, HM8143, NGL200, NGM200, M3SR IN4000A
04-Nov-2019
This application note describes remote operation or monitoring of the signal and spectrum analyzers R&S® FSV3, R&S® FSV7, R&S® FSV13, R&S® FSV30 through a standard web browser. The common cross-platform technology Virtual Network Computing (VNC) is used as a server on the instrument.
15-Jan-2009 | AN-No. 1EF67
Radar test systems are essential in research, development, production and maintenance of radar systems. Most radar tests are expensive to carry out in the field and have a complicated setup and operation. One of the main advantages of the Radar Echo Generator presented in this application note is its ability to generate arbitrary virtual radar echo signals in real time in the laboratory using only commercial measuring equipment. The Radar Echo Generator not only allows to reproduce the results and automate the tests, but also it significantly reduces the measurement effort and costs while providing greater utility for the existing common test equipment. This application note presents a solution for testing the complete radar system by generating any kind of radar echo signals with arbitrary range, Doppler frequency and Radar Cross Section. The Radar Echo Generator makes it possible to perform real time tests on many applications including aerospace & defense and commercial radar systems.
01-Aug-2016 | AN-No. 1MA283
Calibration and Verification Solution
The UWB (Ultra-Wideband) technology is a short range wide-band radio technology specified for device to device communication operating in unlicensed spectrum. It is an RF positioning technology that enables accurate and secure peer-to-peer ranging between mobile devices with robust resistance to interference while consuming very low energy and coexisting well with other radio communication systems. UWB is used for a variety of different applications, such as asset tracking, secure payment, personal tracker, real time location services and keyless access and start of a vehicle etc. According to ABI Research forecasts, there will be well over 1 billion UWB annual device shipments by 2026. Almost every smart phone shipped in 2026 will support UWB services.Talking about testing aspect of a UWB device, in general two test methodologies can be adopted as other wireless products, either the traditional testing mode (so-called conducted test mode) with wired RF connection between the test measurement equipment and device under test (DUT) or over the air (OTA) test mode in an OTA anechoic chamber. Sometimes, it is not always possible or necessary to perform the tests under conducted mode due to the limiting factors, e.g. cost, space, complexity and direct access to the RF connectors of the product. In this case, OTA testing is then becoming a non-evitable approach. Moreover, OTA testing reflects the usage of DUT in a real condition.In this application note, R&S® OTA test solution covering transmitter (Tx), receiver (Rx) and Time of Flight (ToF) testing in Wireless Automated Testing (WMT) environment is described. The measurement results throughout the whole document are based on NXP Trimension™ NCJ29D5 UWB automotive IC.
12-Apr-2023 | AN-No. 1SL394
This application note helps to understand the measurement uncertainty calculation for a modern spectrum analyzer and provides a tool to calculate the total measurement uncertainty for different measurements.
21-Apr-2010 | AN-No. 1EF63
Multiple input multiple output (MIMO) technology is an integral part of 3GPP E-UTRA long term evolution (LTE). As part of MIMO, beamforming is also used in LTE. This application note provides a brief summary of the transmission modes (TM) in LTE and describes the beamforming measurements for base stations (BS) and user equipment (UE). The T&M options using various Rohde & Schwarz instruments are also presented.
26-Apr-2013 | AN-No. 1MA187
The power efficiency of the drive electronics is a key parameter when developing electric drive systems. The conduction loss of the electric drive electronics is of special interest. One important parameter for determining the conduction loss is the RDS(on) of the MOSFET. When a switching MOSFET is off, it has a high drain-to-source voltage, but when it is turned on, the voltage drops to just a few hundred millivolts. A highresolution oscilloscope is needed to measure these low voltages. Probe compensation and correct probing are also vital for accurate RDS(on) measurements.
19-Mar-2015
This application note shows how to perform Bluetooth transmitter measurements with the CMU200 in a reduced signaling mode, in which the protocol handshake between the Bluetooth Equipment Under Test, the EUT, and CMU200 is skipped. This additional CMU200 feature allows both more flexible and faster RF testing of Bluetooth modules. A step-by-step example with SMIQ demonstrates the principles and serves as a reference for integrating this method in user-specific test strategies.
04-Feb-2003 | AN-No. 1MA49
This educational note covers the theory and practice oscilloscopes based on concrete measurement examples that address authentic everyday tasks.The theoretical portion of this paper begins with an explanation of the basic operating concepts for oscilloscopes, followed by a discussion of the most important parameters to be considered when setting up and performing the exercise measurements. The practical portion of the educational note contains detailed measurement tasks that can be performed by small groups in the university lab. These exercises are intended to demonstrate and reinforce the knowledge gained in the theoretical portion. The exercises build upon one another and demonstrate measurement tasks that are frequently encountered by engineers in daily work.
16-Jan-2018 | AN-No. 1MA265
Verification of baseband data is an important step in the early development phase of LTE/LTE-A-ready products. Comparison values for baseband data (test vectors) from other sources can be very useful in order to verify the correct implementation of the standard. Option K81 for the R&S®SMx200A vector signal generator offers sample data for LTE at the bit level. The reference data enables users to test their own implementation of the specification. The LTE bit stream verification program shown here uses data generated by this option and offers a (bitwise) comparison with bit streams generated for an LTE downlink signal. Therefore it demonstrates, how easy the option R&S SMx-K81 can be integrated into the simulation and design process during the development of LTE/LTE-A handsets or base stations.
02-Feb-2011 | AN-No. 1MA161
PESQ measurements employ a level adaptation algorithm and are hence widely insensitive to absolute level. However, if the tests are performed via a speech codec, the driving level of the codec has an influence on the MOS result. Therefore careful alignment of the level is required. This application note provides an application program which runs on the Audio Analyzer R&S UPV or R&S UPV66 and can be used to calibrate signal levels for the PESQ measurement.
30-Jun-2011 | AN-No. 1GA50
The present R&S®SMW-K506 Interface Control Document contains information on► the R&S descriptor word format, including ARB descriptor words and control descriptor words in deterministic and instant mode► Timing requirements and limitations of the interface► Properties of the network interface (Connector designation: HS DIGIQ).It is intended for use by customers using descriptor words to control the R&S®SMW200A in real-time. The interface control document specifies the interface between the customer’s hardware used for provision of descriptor words and the R&S®SMW200A HS DIGIQ interface. Additional information on descriptor word processing inside the R&S®SMW200A is provided.
17-Mar-2022 | AN-No. 1GP134
The application note guides developers and manufactures of Sigfox Devices to perform the required and recommended measurements with test solutions from Rohde & Schwarz. The note will help bring ultranarrowband IoT devices and applications using Sigfox technology to the market as fast as possible and help ensure the desired quality and performance.For R&D, Pre-certification and QA, all currently defined Uplink- and Downlink- measurements are shown using the compact R&S®FPL1000 Spectrum Analyzer and R&S®SMBV100A Vector Signal Generator.For Production, use of the R&S®CMW100A Communications Manufacturing Test Set is shown for the most essential Uplink RF tests on Sigfox Devices.Python scripts for giving example SCPI commands demonstrate how measurements shown in manual use can easily be automated.
15-Nov-2017 | AN-No. 1MA294
The new IP connection security analysis solution for the R&S®CMW500 platform identifies IoT and mobile communications devices’ IP connection vulnerabilities in an early stage of development.
04-Apr-2017
With SMIQ Signal Generator you can generate the most important Bluetooth RF test signals fast and conveniently. This application note comes with files containing modulation data for various payload patterns and burst lengths. A list of patterns is included. With the transfer software, also enclosed with this application note, you can load the data records into SMIQ and start testing immediately. BLUETOOTH is a registered trademark of Telefonaktiebolaget L M Ericsson, Sweden.
30-Jan-2001 | AN-No. 1MA31