Search Application Notes & Cards
Learn how to configure Rohde & Schwarz products to fit your application. Search our database by product, technology, or application to find relevant technical documents.
Search Application Notes & Cards
Learn how to configure Rohde & Schwarz products to fit your application. Search our database by product, technology, or application to find relevant technical documents.
1110 Results
Testing radar warning equipment in realistic scenarios is crucial to reliable field performance. This typically involved dedicated instruments or test systems. Commercial vector signal generators (VSG) such as the R&S®SMW200A from Rohde & Schwarz have become a very attractive alternative thanks to their increased available bandwidth and processing power.
13-Aug-2020
Vector network analyzers are the most accurate instruments in the microwave engineer’s lab. The R&S®ZNA takes accuracy to a new level. Not only is the instrument extremely precise, but now it also calculates and displays the measurement uncertainty right on the screen as the device under test is being measured.
19-Jul-2021
For measurement settings below 10 mV/div, oscilloscopes typically reduce the measurement bandwidth in order to keep the trace noise as low as possible. The R&S®RTO is different: It offers the full bandwidth even for the most sensitive settings, and an A/D converter with more than 7 effective bits (ENOB) digitizes the signal.
13-Jul-2012
Oscilloscopes are the workhorses for power electronics engineers. With powerful and easyto- use FFT analysis capabilities, their application fields extend to EMI debugging – and that saves a lot of time and money. A typical task is verifying the effectiveness of an EMI filter – early in the development phase.
23-Sep-2019
Noise Power Ratio Signal Generation and Measurement
Noise Power Ratio (NPR) is an add-on tool for WinIQSIM™ to generate noise power ratio stimulus signals and measure the resulting noise power ratio of a device under test (DUT) using Rohde & Schwarz instruments via LAN or GPIB bus.
06-Nov-2015 | AN-No. 1MA29
With a Rohde & Schwarz oscilloscope
29-Dec-2018
Software tool for fast and repeatable optimization of signal analyzer RF front-end settings
The signal conditioning in the RF front-end of signal analyzers is crucial to achieve the best performance with respect to image-suppression, noise-floor, dynamic range and other RF-key parameters.Precise signal levelling is especially important for complex measurements like Error-Vector-Magnitude (EVM). To minimize the measurement uncertainty from test system contributions over a wide range of different levels, the RF front-end needs to be adapted continuously according to the signal characteristics, signal power and frequency - ideally using an automatic levelling algorithm.This document describes the approach of a waveform specific, on-site characterization of the signal analyzer: For each waveform and frequency of interest, the instrument is evaluated in a first step. With this additional data, a fast and repeatable auto-levelling can be performed during the actual measurement.
24-Jan-2022 | AN-No. 1EF111
Long acquisitions at maximum resolution with the history function
01-Dec-2017
The R&S®ZNA vector network analyzer with integrated LO output and direct IF input options is a simple, cost-effective solution for 2-port and 4-port measurements using Rohde & Schwarz mmWave converters.
27-Apr-2023
Next generation technologies in radar and satellite communication with high data rates call for innovative testing solutions to develop and manufacture RF components like voltage controlled oscillators (VCO). The R&S®FSPN phase noise analyzer increases efficiency and reproducibility of VCO characterization and phase noise measurements from lab to production.Voltage controlled oscillators are oscillators whose output frequency is controlled by means of an external tuning voltage, and they are used in a wide variety of electronic and RF applications like function generators, phase-locked loops including frequency synthesizers used in communication equipment. Different VCO design approaches yield different parameters and performance, and therefore it is important to measure or characterize VCOs under different conditions. This application note provides a short technical introduction to voltage controlled oscillators and explains the most common and the most important measurements made during the VCO characterization process.
17-May-2023 | AN-No. 1SL386
30 dBm + 30 dBm = 60 dBm? It is well known that it is not as easy as that.
This application note supplies a free of charge software tool that can be used to add or subtract an arbitrary number of powers. In addition, the software can be used to convert power and voltage units from the linear to the logarithmic scale (and vice versa), convert linear power and voltage ratios to decibels, and convert a VSWR to other reflection quantities.
10-Dec-2018 | AN-No. 1GP77
This application note describes Methods of Implementations (MOI) for precise, fast and error-free compliance testing of high-speed backplanes and direct attach copper cables (DAC) according to InfiniBand EDR and HDR specifications, based on 25 Gb/s and 50 Gb/s signaling per lane with vector network analyzers from Rohde & Schwarz.
07-Apr-2021 | AN-No. GFM357
Ethernet communications has been introduced in automotive networks to enable fast and cost efficient data communications, e.g. for the rearward camera or audio/video streaming. In the OPEN alliance (www.openSIG.org), the automotive industry has standardized the BroadR-Reach® physical layer as the automotive Ethernet communications standard. It will be part of the IEEE 802.3 standard. BroadR-Reach® uses full duplex twisted pair communications, enabling 100 Mbit/s data transfer. For interface verification the OPEN Alliance has specified a BroadR-Reach® conformance test with six test cases.
27-Mar-2015
EMI compliance is becoming a major concern for advanced power electronics due to increasing switching speeds. Correlated time-frequency measurements help optimize gate driving and minimize electromagnetic emissions early on during development.
22-Nov-2018
Over the past few years, electronics developers have developed a variety of approaches to avoid interference on high-speed signals on printed circuit boards. However, with increasing complexity and frequency, PCBs set new limits, supporting frequencies of 40 GHz and higher. Driven by the fast growing 5G market, today’s digital systems operate in these high frequency ranges that come with completely new challenges. With slope steepness’s of just a few picoseconds, any discontinuity in the impedance and impairment of the inductance or capacitance on the PCB or back drill defects on the PCB can have a massive impact on the signal quality. The industry recognizes that there is a growing need for functional high-speed testing of PCBs. The MicroCraft® E2V6151 series combined with an R&S®ZNB vector signal analyzer delivers a fully automated solution.
25-Mar-2020
This application note reviews the measurement uncertainty analysis and traceability for phase noise with the new R&S®FSWP Phase Noise Analyzer.It describes the new approach for measuring phase noise with the R&S®FSWP using direct downconversion with cross correlation and focuses on traceability using a derived primary measurement standard.
05-Jul-2016 | AN-No. 1EF95
The power efficiency of the drive electronics is a key parameter when developing electric drive systems. The conduction loss of the electric drive electronics is of special interest. One important parameter for determining the conduction loss is the RDS(on) of the MOSFET. When a switching MOSFET is off, it has a high drain-to-source voltage, but when it is turned on, the voltage drops to just a few hundred millivolts. A highresolution oscilloscope is needed to measure these low voltages. Probe compensation and correct probing are also vital for accurate RDS(on) measurements.
19-Mar-2015
Gated spectrum method with the R&S®PR200
03-Feb-2020
Impedance measurements with vector network analyzers require maximum precision. The R&S®ZNL is able to characterize a broad range of impedances with the lowest uncertainty among its competitors in the same class.
02-Oct-2019
The application note guides developers and manufactures of Sigfox Devices to perform the required and recommended measurements with test solutions from Rohde & Schwarz. The note will help bring ultranarrowband IoT devices and applications using Sigfox technology to the market as fast as possible and help ensure the desired quality and performance.For R&D, Pre-certification and QA, all currently defined Uplink- and Downlink- measurements are shown using the compact R&S®FPL1000 Spectrum Analyzer and R&S®SMBV100A Vector Signal Generator.For Production, use of the R&S®CMW100A Communications Manufacturing Test Set is shown for the most essential Uplink RF tests on Sigfox Devices.Python scripts for giving example SCPI commands demonstrate how measurements shown in manual use can easily be automated.
15-Nov-2017 | AN-No. 1MA294
A new phase noise test instrument covers the frequency range from 1 MHz to 50 GHz with direct down-conversion analog I/Q mixers and baseband signal sampling. The traditional PLL has been replaced by a digital FM demodulator for phase detection and frequency tracking. An additional AM demodulator enables concurrent measurement of phase and amplitude noise. The instrument can measure phase noise as low as -183 dBc/Hz with a 100 MHz carrier frequency and 10 kHz offset within two minutes.
09-May-2016
Rohde & Schwarz presents the R&S®ATS1000 antenna test system, a highly accurate solution for testing 5G antennas up to mmWave frequencies in a mobile shielded chamber.
17-Oct-2017
The R&S®SMW200A together with the R&S®FSW is a state of the art testing solution that significantly reduces the required hardware for testing power amplifiers with envelope tracking and/or digital pre-distortion. This application note introduces the test solution in detail and presents corresponding measurement examples.
25-Sep-2014 | AN-No. 1GP104
Reflection measurements are a common way of assessing antenna system performance. When a minimum amount of the transmitted signal is reflected, it indicates that the transmission energy can reach the intended coverage. Undesired high reflection causes the system to be inefficient and can damage components. Reflection measurements can be expressed in terms of return loss, VSWR and reflection coefficient.
13-Nov-2017
Before devices can be used in a LoRaWANTM network, they must among other things meet country-specific wireless communications regulations. This application note shows developers and manufacturers of devices with LoRa wireless technology how transmitter measurements are conducted in line with FCC Part 15.247. It also describes how important receiver characteristics can be verified by metrological means. In this context, battery life in particular plays a key role in IoT applications. A further chapter describes how current consumption of LoRa wireless modules can be measured reliably.
29-Nov-2017 | AN-No. 1MA295
Timing components such as low jitter oscillators and clocks are necessary to facilitate increasing data rates in high speed digital designs. As part of the overall system design, the components also have to perform in the system’s non-ideal power integrity environment and limit the power supply induced phase noise and jitter from power rail disturbances. Measuring the power supply noise rejection (PSNR) requires accurate generation and leveling of artificial, sinusoidal disturbances and measurement of resulting phase-noise and jitter impairments.
30-Sep-2020
This application note describes Battery Life Measurements with the R&S®RT-ZVC02/04 Multi-Channel Probe. The measurements are described with the use of an oscilloscope. The R&S®RT-ZVC Multi-Channel Probe can be used with R&S®RTE1000, R&S®RTO2000 or R&S®RTP.
17-Jan-2019 | AN-No. 1TD07
NGM200, NGL200 The R&S®NGL200 and R&S®NGM200 can simulate battery cells when testing battery management systems and replace far more expensive dedicated battery simulators. Testing battery management systems with Rohde & Schwarz power supplies NGM200, NGL200 The R&S®NGL200 and R&S®NGM200 can simulate battery cells when testing battery management systems and replace far more expensive dedicated battery
08-Jun-2020
Well-matched RF ports are a crucial aspect to any RF system. Matched ports, for example, protect amplifier output ports from reflected power overload. This undesired reflected power could destroy the whole amplifier. Matched ports also maximize power transmission, effectively extending the battery life of wireless products such as those made for the internet of things (IoT).
05-Mar-2020