Search Application Notes & Cards
Learn how to configure Rohde & Schwarz products to fit your application. Search our database by product, technology, or application to find relevant technical documents.
Search Application Notes & Cards
Learn how to configure Rohde & Schwarz products to fit your application. Search our database by product, technology, or application to find relevant technical documents.
1108 Results
Simulation can be a big time-saver when designing EMI filters for DC/DC converters. Power supply control chip vendors offer various filter design tools that provide reasonable design choices for filter simulation before any hardware prototype is available. However, simulated results can differ significantly for different tools if simulated models are not accurate or do not cover all the relevant components. Performing a hardware measurement to evaluate the effectiveness of a simulated EMI filter is therefore indispensable.
21-Sep-2021
This application note shows how to use Rohde & Schwarz signal generators and analyzers for testing early 5G New Radio components, chipsets and devices. Methods for easy creation and analysis of custom OFDM are explained. The solution provides● a single user interface for signal generation and analysis configuration● Flexible OFDM configuration and signal generation incl. flexible pilot and data allocation● User defined modulation schemes including complex scenarios, e.g. 5G NR PSS
23-Oct-2017 | AN-No. 1MA308
conducted conformance testing according to TS 38.141-1, Rel. 15
3GPP defines the Radio Frequency (RF) conformance test methods and requirements for 5G NR Base Stations (BS) in the technical specifications TS 38.141. This application note describes how all mandatory RF receiver tests (TS 38.141-1, chapter 7), according to Release 15, can be performed quickly and conveniently with signal generators from Rohde & Schwarz by either choosing manual operation or a remote control approach. Moreover, one test case requires a signal or spectrum analyzer from Rohde & Schwarz which is highlighted seperately in the corresponding chapter.In Addition, a new Python software library comes with this application note to enable the remote control approach of base station testing. This example requires the RsInstrument module which can be found on pypi.org or installed via 'pip' and is provided as is.
02-Dec-2020 | AN-No. GFM314
EMI compliance is becoming a major concern for advanced power electronics due to increasing switching speeds. Correlated time-frequency measurements help optimize gate driving and minimize electromagnetic emissions early on during development.
27-Apr-2023
With the start and spread of 5G communications services and new form factors such as wearables and foldable phones, an increasing number of flexible printed circuit boards (PCB) that support high frequency signals are being produced. These boards must exhibit excellent frequency characteristics. In the past, a PCB’s frequency characteristics were subjected to sampling inspection using a test coupon. For flexible PCBs, a new method is needed to provide repeatable and proper verification. The Yamaha® MP Series combined with the R&S®ZNBT vector network analyzer measure the high frequency characteristics of a production lot at high speed and high accuracy, enabling 100 % measurement of mass produced rigid and flexible PCBs.
27-Jan-2020
Today’s digital designs and high-speed data converters require clean clocks with minimal jitter
03-Aug-2017
Generation of wideband digital modulated signals in V-band and above is a challenging task and typically requires a set of multiple instruments. This application note aims at simplifying the task and looks into the analysis part as well. Latest signal and spectrum analyzers like the R&S®FSW67 and R&S®FSW85 are first to allow use in V-band up to 67 GHz and E-band up to 85 GHz respectively without external frequency conversion. Up to 8.3 GHz of modulation bandwidth can be covered using the R&S®FSW-B8001 option. Millimeter wave use of analyzers ranging from 26 GHz up is shown. Application note 1MA217 describes V-band signal generation and analysis up to 500 MHz modulation bandwidth. This application note expands modulation bandwidth up to 2 GHz and covers both V- and E-band examples.
18-Jun-2015 | AN-No. 1MA257
The R&S®TSStream multi-TS streaming software streams a number of MPEG transport stream files simultaneously over a single IP interface. The individual transport streams result in a high overall bit rate. To make the streams available on a standard PC, the R&S®TSStream software does not play the transport stream files directly from the hard disk but first loads them into the RAM. The maximum number and length of the transport streams depends solely on the PC's available RAM.
16-Mar-2017 | AN-No. 1GP113
This application note describes the basic frequency filter measurements that are often required during service repairs, during development of simple circuits and for training purposes. These measurements do not always require high-end T&M equipment. Instruments in this class typically offer a very wide range of measurement functions coupled with the best-possible RF performance. However, these features are not necessary for simple applications. This application note therefore describes measurements using instruments from the cost-effective Rohde & Schwarz Value Instruments series. The instruments in this series offer the measurement accuracy demanded by quality-conscious users plus easy operation and all of the functionality needed for everyday measurement tasks.
27-Mar-2015 | AN-No. 1MA243
The topic of this application note is mobile phone measurements – in theory and in practice. It discusses measurements according to the most common standard in use today, GSM.The first, theoretical portion of this application note covers digital modulation and access methods in general. This is followed by an overview of the specific characteristics of the GSM standard as well as a summary of the most important mobile radio measurements.The second, practical portion of this application note covers some of these measurements in detail and runs through them step by step. These measurements can be performed by small groups in labs.The measurements and analysis of the results are intended to illustrate the theoretical portion of the application note and to deepen the reader's understanding.All measurements are performed using the R&S®CMW500 wideband radio communication tester and an off the shelf mobile phone.
22-Aug-2014 | AN-No. 1MA231
LTE is becoming the predominant wireless technology. Among several new features of this standard, the multiple input multiple output (MIMO) technology offers various advantages. It improves the throughput, extends the reach, reduces interference and improves the signal to interference plus noise ratio (SINR) with beamforming. LTE supports various modes in order to optimize the transmission settings. An LTE MIMO base station consists of a baseband unit, a remote radio head (RRH) and an array of up to eight antennas. The RRH upconverts the digital signals of the baseband unit into analog signals for each antenna.
16-Aug-2016
The R&S CMW500/270 can generate and measure standard-compliant WLAN IEEE 802.11ac signals with bandwidths from 20 MHz up to 160 MHz.This document explains the CMW solution for the signals with 160 MHz bandwidth and describes the required configurations step by step.
21-Oct-2013 | AN-No. 1CM101
For measurement settings below 10 mV/div, oscilloscopes typically reduce the measurement bandwidth in order to keep the trace noise as low as possible. The R&S®RTO is different: It offers the full bandwidth even for the most sensitive settings, and an A/D converter with more than 7 effective bits (ENOB) digitizes the signal.
13-Jul-2012
This application note describes Methods of Implementations (MOI) for precise, fast and error-free compliance testing of high-speed backplanes and direct attach copper cables (DAC) according to InfiniBand EDR and HDR specifications, based on 25 Gb/s and 50 Gb/s signaling per lane with vector network analyzers from Rohde & Schwarz.
07-Apr-2021 | AN-No. GFM357
More and more mobile radio networks implement remote radio equipment (RE) that is connected to the base station main unit via a digital interface using standardized transmission protocols such as CPRI. For testing RE devices Rohde & Schwarz offers a complete test solution based on the R&S®EX-IQ-BOX [Model K04]. This key component is a configurable digital interface module that is used to connect Rohde & Schwarz test equipment to a RE under test using CPRI data transmission. This application note explains in detail the instrument setup and configuration needed to successfully test your remote radio head.
05-Aug-2013 | AN-No. 1GP78
Enhanced Mobile Broadband, Massive Machine Type Communication, Ultra-reliable and low latency communication have been identified as the requirements to be supported by the 5thGeneration of Mobile Communication, short 5G. 5G is extensively discussed in the wireless industry. A lot of research and pre-development is being conducted worldwide, including an analysis of the waveforms and access principles that are the basis for current LTE and LTE-Advanced networks.In this application note we discuss potential 5G waveform candidates, list their advantages and disadvantages and compare them to Orthogonal Frequency Division Multiplexing (OFDM), which is used in LTE/LTE-Advanced.
10-Jun-2016 | AN-No. 1MA271
This application note describes remote operation or monitoring of the signal and spectrum analyzers R&S® FSV3, R&S® FSV7, R&S® FSV13, R&S® FSV30 through a standard web browser. The common cross-platform technology Virtual Network Computing (VNC) is used as a server on the instrument.
15-Jan-2009 | AN-No. 1EF67
Multiple input multiple output (MIMO) technology is an integral part of 3GPP E-UTRA long term evolution (LTE). As part of MIMO, beamforming is also used in LTE. This application note provides a brief summary of the transmission modes (TM) in LTE and describes the beamforming measurements for base stations (BS) and user equipment (UE). The T&M options using various Rohde & Schwarz instruments are also presented.
26-Apr-2013 | AN-No. 1MA187
The power efficiency of the drive electronics is a key parameter when developing electric drive systems. The conduction loss of the electric drive electronics is of special interest. One important parameter for determining the conduction loss is the RDS(on) of the MOSFET. When a switching MOSFET is off, it has a high drain-to-source voltage, but when it is turned on, the voltage drops to just a few hundred millivolts. A highresolution oscilloscope is needed to measure these low voltages. Probe compensation and correct probing are also vital for accurate RDS(on) measurements.
19-Mar-2015
Verification of baseband data is an important step in the early development phase of LTE/LTE-A-ready products. Comparison values for baseband data (test vectors) from other sources can be very useful in order to verify the correct implementation of the standard. Option K81 for the R&S®SMx200A vector signal generator offers sample data for LTE at the bit level. The reference data enables users to test their own implementation of the specification. The LTE bit stream verification program shown here uses data generated by this option and offers a (bitwise) comparison with bit streams generated for an LTE downlink signal. Therefore it demonstrates, how easy the option R&S SMx-K81 can be integrated into the simulation and design process during the development of LTE/LTE-A handsets or base stations.
02-Feb-2011 | AN-No. 1MA161
PESQ measurements employ a level adaptation algorithm and are hence widely insensitive to absolute level. However, if the tests are performed via a speech codec, the driving level of the codec has an influence on the MOS result. Therefore careful alignment of the level is required. This application note provides an application program which runs on the Audio Analyzer R&S UPV or R&S UPV66 and can be used to calibrate signal levels for the PESQ measurement.
30-Jun-2011 | AN-No. 1GA50
Part 1 of the Cable and Antenna verification series – essential for Mobile Networks
Key points: Critical Infrastructure: Learn why the antenna system, as part of mobile base stations, is irreplaceable and demands meticulous attention due to its impact on network quality and availability.Vulnerability to Environmental Factors: Understand the challenges posed by weather conditions and environmental stresses on antenna systems, highlighting the importance of robust design and maintenance.Fundamental Properties: Delve into the core concepts of antenna systems, gaining insights into their transmit and receive characteristics, which serve as the foundation for effective measurement and verification.Measurement Techniques: Explore various measurement methods for antenna systems, focusing on return loss and decoupling, and their significance in assessing system performance and integrity.
23-Feb-2024 | AN-No. 8NT11
Noise figure is an important parameter that describes the noise contribution of an electronic device. A classical approach to measure the noise figure is to use a noise source which delivers two different input noise powers by switching between a “hot” and a “cold” state and a noise receiver (e.g. a spectrum analyzer).In contrast to this approach, using a vector network analyzer with the “Cold Source” approach eliminates the need for a noise source. A cold source noise power measurement followed by an available gain measurement of the device under test is sufficient to determine the noise figure of the device. This application note describes the “Cold Source” technique for measuring noise figure on the R&S®ZNA family of vector network analyzers.Background equations are provided for an analysis of noise factor, noise figure and noise temperature on a device under test and a cascade of devices.Based on a measurement example the user will be guided through the process of setting up a noise figure channel and performing a noise figure measurement. In addition, various measurement options are reviewed, providing guidance as to when and how each option should be utilized to improve the noise figure results.
23-Dec-2021 | AN-No. 1SL378
A new phase noise test instrument covers the frequency range from 1 MHz to 50 GHz with direct down-conversion analog I/Q mixers and baseband signal sampling. The traditional PLL has been replaced by a digital FM demodulator for phase detection and frequency tracking. An additional AM demodulator enables concurrent measurement of phase and amplitude noise. The instrument can measure phase noise as low as -183 dBc/Hz with a 100 MHz carrier frequency and 10 kHz offset within two minutes.
09-May-2016
Rohde & Schwarz presents the R&S®ATS1000 antenna test system, a highly accurate solution for testing 5G antennas up to mmWave frequencies in a mobile shielded chamber.
17-Oct-2017
Offering bandwidths up to 160 MHz, the signal generators and analyzers from Rohde & Schwarz are ideal for testing IEEE 802.11ac signals
27-Jun-2013
The R&S®SMW200A vector signal generator has the outstanding ability to simultaneously generate up to eight independent signals from a single instrument. The advanced multi-channel architecture allows realizing even complex applications like MSR, carrier aggregation, MIMO or enhanced interference scenarios with a minimum of effort.This application note gives an overview of common multi-channel application examples and how to equip the Rohde & Schwarz signal generator R&S®SMW200A appropriately.
12-Mar-2018 | AN-No. 1GP106
This document describes how the advanced calibration techniques of the ZVA Vector Network Analyzers can solve the challenges of measuring the S-Parameters on impedance matching devices. The document describes the concept and setup required to perform the calibration of the ZVA and making the measurement. The procedure described in this application note applies to the ZVB and ZVT Vector Network Analyzers as well.
06-May-2009 | AN-No. 1EZ59
The R&S®SMW200A together with the R&S®FSW is a state of the art testing solution that significantly reduces the required hardware for testing power amplifiers with envelope tracking and/or digital pre-distortion. This application note introduces the test solution in detail and presents corresponding measurement examples.
25-Sep-2014 | AN-No. 1GP104