52 Results
ZNB - several channels with external trigger
Bias tee limits and calibration considerations
I got a calibration kit with a sliding match standard. But there are no correction values for the NWA supplied.
Active cal kit or cal unit does not contain all standards needed for selected cal procedure.
How do I use the driver correctly?
I need to activate the deembedding function on a specific port. The data is available on a touchstone file (s2p) How can I load the file with remote commands?
Calibration of two channels simultaneously with remote commands
VNA - do I really need a sliding match for calibration?
What can I do to avoid that difference between my screen and the print?
I have used my TRL calibration kit with my ZVA before. Now I want to use also with my ZNB. But when I try to load the data of the calibration kit into the ZNB, the above error message is shown.
SCPI remote error message on the display
External generator connected via USB not correctly recognized
Improve the calibration procedure for different setups
Save/recall files: own folder in 'Look In'
I am using the command “CONT:AUX:C x” to see when a channel is active. But the respective pin at the AUX connector does not switch to “high”.
ZNB - print to file command does not work anymore
ZNA/ZNB: Export all mixed mode S-Parameters
ZNB - How to disable Sweep Position Display Symbols
ZNB, ASCII export of displayed trace values
The user is requested to move results from a Network Analyzer to the controller PC or to a network drive.
Installing a USB-GPIB adapter
When I start a calibration with an auto cal unit I get the following warning. What does that mean?
Is it possible to automatically restart a ZNB with return of the AC power?
License Keycode for VNAMUC is not accepted
Is there a way to query the data of all traces at once?
ZNB/ZND - wrong connector type shown at Cal Unit Characterization
The MINUS key on the keypad does not work.
Remote control autocalibration with a calibration unit
When I export the time domain trace the stimulus values are in Hz, but not in seconds as shown on the screen. How can I get the export in time or distance?
I have done a calibration and now I want to validate it with an automatic calibration kit. But it always fails. What is wrong?
How can I export the traces of a specific channel into one file, i.e. CSV?
I perform a calibration with remote commands. With the command to start the calibration sweep with a short standard I get this error message. What is the problem?
TRL calibration - middle of line or end of line
Remote Desktop connection
ZNA, ZNB, ZND - Power off after stop of the Sweep?
I want to do a calibration with 75 Ohms at the ZNB/ZND/ZVA. Do these VNAs accept the auto cal unit ZV-Z53 with 75 Ohms impedance?
I have several traces with markers in one channel. When I query the result of marker 1 I always get the response of trace 1. How can I get the result of marker 1 for trace 2?
Remote Desktop screen size of ZNB/ZND
I want to control my Analyzer using Remote Desktop from my PC. My Analyzer does not react.
ZNB: Power off at sweep end possible?
I have a file on my device. How can I get it in a simple way to my PC?
Reverse sweep / backward sweep
Store several diagrams in one file and each diagram on its own page
Calibrating a vector network analyzer (VNA) with different connectors on each port
Is there a way to use the hard keys when using the ZNB via Remote Desktop connection? On my unit I only see the standard menu to the lower left side of the device, but have no access to the "master keyboard"
How do I calculate these frequency points when I have a logarithmic sweep and know the center frequency, the span and the number of sweep points?
I have an existing limit line. Is it possible to apply a vertical offset?
Export complex data of a trace with mathematics and time gating.
Restore the Auto Logon Configuration
I query the values of a trace using scpi commands. But I get the y-values only. Is there a possibility to get the y-values also (frequency)?
Can the option ZNB-B10 be installed in the field?
I would like to use the ZNB as a signal generator. I need a CW signal on port 1 and port 3 with different frequencies. How can I get that?