447 Results
I want to use the LCX series LCR Meter to automatically control and sort components. One of the tasks is to differentiate between the following three values of resistors: - Less than 990 Ohm, - Middle range from 990 to 1010 Ohm (1 kOhm), - More than 1010 Ohm. How can I set this measurement up and which pins do I have to use at the 15 PIN SUB-D socket at the rear side of the LCX?
The R&S®CMW100 communications manufacturing test set with a supported bandwidth of 160 MHz is ready for testing initial 5G NR sub-6 GHz wireless devices in production. The video demonstrates a typical manufacturing test case using a 5G NR-like waveform.
The intensity button lets you set the level of transparency. You can also minimize a dialog box to the active input field and position it anywhere on the screen.
07-Oct-2022
Rohde & Schwarz brings Oscilloscope Days to the next level with School of Measurement live events across EuropeThe Oscilloscope Days educational event at Rohde & Schwarz continues to evolve, combining virtual sessions with a series of in-person events, called the School of Measurement. Starting with a digital kick-off on October 27, 2022, the series is set to last through 2023 with stops at multiple locations across Europe. It will cater to electronics engineers from Europe and beyond. Participation in the seminars is free.
Rohde & Schwarz Getting Started for the R&S®EVSG1000 VHF/UHF Airnav/Com analyzer for air navigation and communication signals, with basic information needed to set up and start working with the instrument. Safety information is also included.
EVM Measurements for ZigBee signals in the 2.4 GHz band
12-Dec-2014 | AN-No. 1EF55
This combined with the highest measurement speed in the market, you will get the needed results in seconds.The R&S5G STS is a must for users who work on performance tuning after site deployment as it is essential to set up a passive test tool, evaluating the radio condition, which are crucial for a good user-experience.
The R&S5G STS is a must for users who work on performance tuning after site deployment as it is essential to set up a passive test tool, evaluating the radio condition, which are crucial for a good user-experience. The Rohde & Schwarz 5G STS is the most modern test tool for a passiv over-the-air network troubleshooting task. It is very intuitive and easy to use.
This application note describes different measurement techniques and methods for an automotive lighting module based on a hybrid controller design.
08-Jun-2020 | AN-No. GFM339
Rohde & Schwarz Getting Started for the R&S®EVSF1000 VHF/UHF Nav/Flight analyzer for air navigation and communication signals, with basic information needed to set up and start working with the instrument. Safety information is also included.
Rohde & Schwarz User Manual for the R&S®TSME6 Ultracompact Drive Test Scanner, including the R&S®TSME Device Manager software.
Transmitter and Receiver Measurements on Bluetooth Modules with CMU200
06-Aug-2001 | AN-No. 1MA46
Rohde & Schwarz application sheet for the R&S®NRQ6 frequency selective power sensor, describing the power servoing function of an R&S®NRQ6 together with an R&S®SGT100A signal generator
Rohde & Schwarz User Manual for the R&S NRPM OTA power measurement solution, including sensor and antenna modules, and information on how to setup and perform basic measurements and remote command description.
A sinus signal with i.e. 10 V peak-peak, frequency 1 MHz is applied. If I choose a vertical scale which is too small the peaks of the waveform are not displayed as they are out of range. Now I activate the digital filter in the “Vertical” menu à “Channel”. The frequency of the filter is also set to 1 MHz. Now even at very small vertical scales (i.e. 50 mV/div) the waveform is displayed completely, see screenshot. But the amplitude can not be correct. What goes wrong here?
Carrier aggregation is the most demanded feature of the LTE-Advanced feature set because it will allow network operators worldwide to aggregate their different spectrum holdings.
Chipset manufacturers for TV sets, set-top boxes and radios EMC test house engineers TV and radio network operators Car manufacturers and car system integrators (automotive) Infotainment systems manufacturers Car radio chipset manufacturers EMC test houses RED, DAB, R&S®BTC In this webinar we will demonstrate, step by step, how to perform audio measurements on a DAB car radio receiver with the R&S®
Generation and Measurement of Burst Digital Audio Signals with Audio Analyzer UPD
05-Nov-1997 | AN-No. 1GA38
Advanced Signal Analysis using the History Mode of the R&S RTO Oscilloscope.
03-Jun-2013 | AN-No. 1TD02
This application note describes how noise figure and gain of amplifiers or converters in the microwave range from 50 GHz to 67 GHz are measured.
12-May-2009 | AN-No. 1EF64
Storing and Loading Complete Test Receiver Data Records via IEC/IEEE-Bus
18-Jan-2002 | AN-No. 1EE20
4-Port Measurements with Vector Network Analyzer ZVR
28-Jul-1998 | AN-No. 1EZ25
IEEE 802.16m Technology Introduction
29-Jul-2010 | AN-No. 1MA167
R&S MATLAB<sup>®</sup> Toolkit for R&S<sup>®</sup> NRP-Z Sensors
05-Mar-2011 | AN-No. 1GP61
The terrestrial television standard DVB T2 is gaining in significance as a result of the growing scarcity of available frequencies. New systems are being tested in many countries around the world. Other countries have already completed the introductory phase for DVB T2. Broadcasting transmitters are subject to particularly stringent standards with respect to broadcast signal quality, because even small faults can lead to service disruptions for many viewers or even disrupt adjacent channels.A single instrument, the R&S®ETL TV analyzer, performs all required DVB-T2 transmitter measurements, from the initial acceptance testing for the transmitter, to measurements performed during commissioning and preventive maintenance.The measurements described here satisfy many country-specific and customer-specific test specifications. Users need only set the limit values accordingly.
23-Jul-2014 | AN-No. 7BM106
WCDMA RF Measurements with the R&S<sup>®</sup>CMW500 according to 3GPP TS 34.121
16-Dec-2011 | AN-No. 1CM95
The R&S®ZNB measures the signal integrity on the PCB, taking the needed test fixtures and probes into consideration – a complete solution in a compact format.
25-Mar-2020