Search Rohde-Schwarz.com
Find the information you need from Rohde & Schwarz. Search for products, technologies, applications, manuals, datasheets, tutorials, FAQs, and more.
Search Rohde-Schwarz.com
Find the information you need from Rohde & Schwarz. Search for products, technologies, applications, manuals, datasheets, tutorials, FAQs, and more.
794 Results
I would like to measure the voltage at a certain time of a captured waveform. Do I need to use the cursor function? May I ask for the SCPI commands?
When I export the time domain trace the stimulus values are in Hz, but not in seconds as shown on the screen. How can I get the export in time or distance?
I want to use the Digital I/O Pins on my NGE series PSU, but could not find some information in the manual.
The Zoom function does not show any waveform data at specific settings, especially at slower timebases in combination with higher sample rates, High resolution and roll mode with more channels. The problem is gone if a lower sample rate is chosen.
Is is possible to use the differential probes RT-ZD02 or RT-ZD08 on oscilloscopes with high impedance? The impedance of the RT-ZD02/ZD08 is 50 Ohms.
I query the values of a trace using scpi commands. But I get the y-values only. Is there a possibility to get the y-values also (frequency)?
Sometimes when I start the XRT100 measurement, the CMA application returns a connection error. What can I do to avoid this problem?
I have a file on my device. How can I get it in a simple way to my PC?
How to see the graphic of a modulated signal to be downloaded to the signal generator SMBV100A, SMBV1000B, SMW200 with the WINIQSIM2.
During the call setup with VoLTE/VoWiFi with EVS voice codec the bandwidth is negotiated. How can the bandwidth be setup and how will it be shown in the CMW user interface?
I need to activate the deembedding function on a specific port. The data is available on a touchstone file (s2p) How can I load the file with remote commands?
I am using R&S ELEKTRA with EMI Receiver for conducted measurements with a LISN. During installation and first measurement, we had the "IFOVLD" error, what does mean results are invalid.
We have installed our test system with EMC32 and all devices, but NRP2 can not be set to physical from EMC32 using LAN interface.
For radiated emissions test I would like to change the antenna factors to another antenna. Would it be possible to get a step by step guide as to how to create a new radiated emissions test using my EMI Test Receiver receiver with a new antenna?
How can I switch from remote to local state via remote control?
I want to use the "Remote Display" function of the Instrument View software. Instead of the screen I just see a "white" area. My PC is connected via USB. How can I use it?
I want to connect my HE400 to my handheld devices. Unfortunately I don't know which adaptor cable I need for that task. Is there an overview available?
I tried to measure the Voltage Noise of my power supply unit which is specified to the following values. My results have been much higher and I sent in the device for alignment/calibration. After getting it back I still gather the same results. Can you explain how to perform such a measurement?
Is it possible to have multiple access to the HMP series PSUs via TCP/IP? I want to control the device from two different applications and keep the connections open all the time.
I want to expand the output power of my PSU using some channels in parallel. How can I use sensing in that case?
If a CMWrun test plan script has been fished the AC power of a CMW500 / CMW290 / CMW270 should be shut down automaticly.
I would like to connect a controller with EMC32 program and measure the disturbance field strength with at a certain distance in sync with motorised rail. I would like to setup the communication between my controller and EMC32. Can you send me some instructions for communication between EMC32 and external hardware?
I followed steps to determine an IP address to my NRP series sensor. Unfortunately without no success as I can not find the sensor at all.
Some parts of my program cause timeouts. Is it possible to track the traffic via my VISA installation? It would help me a lot to see the complete command flow including timing information
I am using the I/O Logging function to write all remote commands sent to the ZNL(E) to file. But I can not find any logging file in the path mentioned in the manual: C:\ProgramData\Rohde-Schwarz\ZNL-FPL\ScpiLogging
I would like to be sure about the high impedance state of a dedicated channel for my power supply unit. Do you have a process to test and to ensure that? Can you also please explain, how the high impedance mode works?
How do I calculate these frequency points when I have a logarithmic sweep and know the center frequency, the span and the number of sweep points?
I created an arbitrary waveform using a remote control program. I am struggling to find the according SCPI command to trigger the sequence. At the moment I can only trigger it manually using the button on the device. Is there a way to do this completely by remote control?
I have used my TRL calibration kit with my ZVA before. Now I want to use also with my ZNB. But when I try to load the data of the calibration kit into the ZNB, the above error message is shown.
Sense protection request on NGx series PSU during remote control