Show Graphic of a Transducer using EMC32

Submit frequency and level from EMC32 to Vector CANoe.

How can I add a attenuation table to my cable, used in my measurement setup?

Welcome to our webinar "Basic Introduction to the New R&S EMC Software “Elektra” the Successor of the famous R&S®EMC32".

In the Graphics of a Test, is it possible to make the Legend is always on? So we don't need to insert it, every time the Test is finished?

Using R&S®ELEKTRA Migration Tool

The R&S®ELEKTRA EMC test software is the successor of the R&S®EMC32 EMC measurement software. Like the R&S®EMC32 EMC measurement software, the R&S®ELEKTRA offers a solution that controls complete EMC systems and automates measurements on equipment under test (EUT) that is being tested for emissions (EMI) and immunity (EMS) compliance. It has more features and test types compared to R&S®EMC32.As both software platforms use different file formats, R&S®EMC32 users who upgrade their existing software to the R&S®ELEKTRA platform need to perform a file conversion before migrating their data to the R&S®ELEKTRA platform. This is done by using the R&S®ELEKTRA Migration Tool, which is installed automatically with each R&S®ELEKTRA installation.This Application Note describes how to use the R&S®ELEKTRA Migration Tool (version 4.4 onwards) for converting the backup data into the XML format that can be interpreted by the R&S®ELEKTRA software. It also provides recommended conversion steps (Chapter 5) and troubleshooting tips (Chapter 6). For instructions on migrating the data using R&S®ELEKTRA Migration Tool below version 4.4, refer to the R&S®ELEKTRA user manual. For better user experience, we recommend using the latest software version for migration.This Application Note does not describe the steps to backup data using the R&S®EMC32 or R&S®ES-SCAN software. For procedures on how to do so, refer to their respective manuals.

04-May-2023 | AN-No. 1SL396

When I run the Test and go back to change the parameters in Test Template, how do I save the new settings?

Updating API macros in EMC32

I am going to migrate EMC32 system in ELEKTRA using the Migration Tool. It seems the Migration Tool has a problem reading the DeviceList.

I am using EMC32 with EMI Auto Test EMC32-K10 and Test Receiver ESCI. The issue is I cannot perform final measurements with the detector CISPR AV.

I recently exported the results table from a test, and realized it had been truncated at line 65535. I tried a few more times, but the result was the same. What is the reason for the limitation?

For radiated emissions test I would like to change the antenna factors to another antenna. Would it be possible to get a step by step guide as to how to create a new radiated emissions test using my EMI Test Receiver receiver with a new antenna?

FAQ. TS8997 waveform files on the vector generator not found

How to connect HMExplorer to the instrument

We need to be able to send both command one by one. Is it somehow possible?

Diffent from the defaults, I would like to perform a disturbance Power test from eg. 300 to 500cm

I would like to do EMI measurements with a Probe. The thing is that I don’t have a "Probes” section in Device List menu. For instance within this menu, I have Generators, Receivers, etc. but not “Probes”.

R&S®EMC32 - Product Brochure

Multichannel audio measurements

update license iKey 9.xx

Use of ELEKTRA on a non-Test-PC.

EMC32-K2 - how to check for availability

FAQ; How to Document Sseveral Measurements in one Test Rreport

Describes the initial installation and all functions of R&S®ELEKTRA.

EMC32-S: RF indicator while running an EMS test

How can I set up EMC32 so that it is possible to measure with the forward and reverse power with NAP?

EMC32 does come with a Device Support list, available from CD ROM / CD download image, showing the minimum firmware version for my instruments. Is this also available for ELEKTRA?

This application note describes how to use the generic interface in R&S®AdVISE for remote operation.

19-Jun-2020 | AN-No. 1S002

This application note describes how to detect even small fails in dynamic turn indicators with R&S®AdVISE.

30-Jul-2020 | AN-No. 1S006

A typical application is EMS testing with R&S®EMC32 or R&S®ELEKTRA test software. This video introduces the tracking feature of R&S®AdVISE. EMC; EMS; EMS Testing; EMC Testing; EMC32; ELEKTRA; AdVISE; Visual Inspection; Optical Inspection The R&S®AdVISE visual inspection software automates the process of visually monitoring equipment under test (EUT) during a test sequence.