The Electromagnetic Disturbance (EMD) emitted by Proximity-Integrated-Circuit-Cards (PICC) is a unwanted form of load modulation. This Application Note describes a method for measuring EMD during data transmission using vector signal analysis

19-Oct-2007 | AN-No. 1MA120

Radio frequencies in bands around 28 GHz are being discussed as candidates for mobile communications of the fifth generation (5G). Beam steering will be a key feature in the context of 5G. It will be a major challenge to test the beam steering capabilities of base stations and user equipment in every phase from research and development through production. Conducted measurements will be mainly replaced by over-the-air measurements of electromagnetic radiation. Rohde & Schwarz offers the R&S®NRPM Over-the-Air (OTA) Power Measurement Solution that perfectly fits such measurement needs.Part of this solution are the R&S®NRPM-A66 antenna modules. They have integrated diode detectors. Thus, there are no cables between the antenna and the detector as in traditional setups. This avoids high and potentially unknown RF losses. The R&S®NRPM-A66 antenna modules with their integrated diode detectors are factory calibrated, which means that the user does not have to calibrate them to achieve highly accurate measurement results.This application note contains theoretical background on OTA power and pattern measurements. It gives step-by-step instructions for the verification of the power level and the radiation pattern of a device under test (DUT) in comparison to a golden device, and it presents an approach for verifying the accuracy of beam steering.

29-Aug-2017 | AN-No. 1GP118

Rohde & Schwarz has a tool that can configure all instruments and channels from one interface to maintain an overview of the states and measurement values for all channels.

28-Apr-2023

The scope of this application note is to give a comprehensive guide on how the R&S®FSW signal and spectrum analyzer with the option R&S®FSW-K18 may be used to create a Hammerstein model for the R&S®SMW200A vector signal generator’s output stage. This model can then be applied to counteract inherent non-linearities and memory effects and improve the Error Vector Magnitude (EVM) at high output powers of the R&S®SMW200A vector signal generator.

28-Aug-2023 | AN-No. 1GP139

The signal purity of clock sources has a direct impact on system performance. To ensure proper operation, it is necessary to verify that the purity meets the design requirements.

30-Sep-2021

Functional Testing

Although data services in the context of eMBB, URLLC and mMTC are the pivotal drivers behind the 5G evolution, legacy services like voice and video communications still represent important services that operators want to offer to their subscribers. As part of the technology evolution, we have seen a major change from circuit-switched 2G networks with an initial focus on telephony to fully packet-switched 4G networks focused on internet data communications.This application note focuses on different details of voice services in 5G networks. Besides some theoretical background this document describes the procedure to setup a 5G network with R&S®CMW500 and R&S®CMX500 radio communication testers and how to carry out different functional voice call tests for 5G networks.

06-Oct-2021 | AN-No. 1SL364

All electronic devices have capacitive or inductive parts that that generate inrush current when switched on. This is more than just a part of operations – it is a vital aspect and demands keen oversight. The R&S®NPA power analyzers are the right instrument for the job.

28-Mar-2024

30 dBm + 30 dBm = 60 dBm? It is well known that it is not as easy as that.

This application note supplies a free of charge software tool that can be used to add or subtract an arbitrary number of powers. In addition, the software can be used to convert power and voltage units from the linear to the logarithmic scale (and vice versa), convert linear power and voltage ratios to decibels, and convert a VSWR to other reflection quantities.

10-Dec-2018 | AN-No. 1GP77

All types of information transmission, including the 'one-way' transmission used in broadcasting, involve feeding a radio frequency (RF) signal to an antenna. This is the essence of the most basic type of transmitter used to emit electromagnetic waves. In the real world, however, a transmitter used for broadcast applications, for example, is much more complex in terms of its functions and design. The different transmitter components must be carefully coordinated. There are many quality parameters that are critical in ensuring that a proper output signal is delivered. Rohde & Schwarz designed the R&S® ETL TV analyzer especially for broadcasting applications. The analyzer allows the measurement of the quality parameters that are relevant in analog and digital broadcasting. This Application Note describes the typical quality measurements performed during compliance testing of TV transmitters. The approach discussed here is based on the example of Rohde & Schwarz terrestrial transmitters for analog TV and DVB-T/H.

19-Sep-2007 | AN-No. 7BM67

This application note explains how to create screenshots of Rohde & Schwarz instruments using instrument drivers. The presented examples are written in C (LabWindows/CVI), C# programming language and LabVIEW. The examples are available at the instrument driver download site.

11-Dec-2009 | AN-No. 1MA160

Sequencer Software Tool

20-Feb-2015

Signaling checks, DSMCC object carousel analysis and fault localization all in one instrument: R&S®DVMS, R&S®DVM or R&S®ETL

28-Dec-2012

Transformers are passive devices that are primarily used to convert or "transform" alternating current (AC) from one voltage level to another. One very common application of transformers is in AC to DC power supplies, in which mains voltage is stepped down before being rectified and filtered to produce DC. There are numerous other applications for transformers, such as providing electrical isolation or for impedance matching.This educational note provides a brief technical introduction to measurements made on the types of transformers used in electronics. These transformers are typically physically small, work on relatively low voltages or powers, and are used for “indoor” applications. Although many of the testing concepts described below also apply to the larger, higher-power "outdoor" transformers used for electrical power distribution, the specific tests and test procedures for these types of transformers are often specified by standards bodies such as the IEEE and may differ substantially from the types of measurements described here.Read this educational note and dive into the discussion about the six most important transformer measurements: turns ratio, mutual inductance, phase angle, primary and secondary inductance, leakage inductance, and interwinding capacitance.

28-Feb-2024

This application note describes Methods of Implementation (MOI) for precise, fast, and error-free compliance testing of USB 3.2 Legacy Cable Testing for USB Type A, Type B, and Micro family connector types. Based on 5 Gbps and 10 Gbps signaling per lane with vector network analyzers from Rohde & Schwarz.

09-Nov-2023 | AN-No. 1SL408

In high-speed digital measurement applications, test fixtures are commonly used to connect devices under test to measurement equipment. Characterization, and analysis in the time and frequency domains that accounts for various constraints helps to remove the influence of these fixtures.

23-May-2023 | AN-No. 1SL393

Noise sources used for noise figure and gain measurements are typically controlled by the spectrum analyzer or noise figure meter instruments and are calibrated with their ENR value (Excess noise ratio). While this external control and the use of ENR values is common in noise figure test, it may be difficult in system applications where the noise source control is not available, and the use of ENR values is replaced with the values for the noise output power of the noise source. The calculation of the output power for the noise source requires to know the P_hot value (hot power) which is not a common specification for noise sources used in test and measurement applications.This application note describes a technique to perform a calibrated noise power measurement (P_hot) with spectrum analyzers and noise sources. The next sections will give further details.

31-May-2022 | AN-No. 1EF113

Describtion and explanation of the MPEG and DVB-Standards and TV T&M

10-Dec-2011 | AN-No. 7BM_ADD01

Embedded power supplies combine traditional power supply components with multiple sensors, processing and control logic as well as digital communications interfaces. Test equipment for debugging requires isolated input channels for measurements of hazardous voltages. Additional digital channels support the analysis of digital signals, while trigger and decode capabilities are essential for time-correlated monitoring of serial protocol-based communications interfaces.

26-Apr-2016

Oscilloscopes are increasingly used to analyze pulsed signals such as radar signals for aerospace and defence as well as automotive applications. The oscilloscopes’ wide analysis bandwidth and manifold trigger capabilities, make them a good fit for the increasing demand for higher bandwidths and accurate signal detection in these applications. R&S®VSE vector signal explorer software is a powerful tool for comprehensive analysis of a variety of signals, providing full support to the Rohde & Schwarz oscilloscope advanced trigger system. Adjusting the trigger settings enables pulses and pulse sequences to be isolated and run full pulse analysis using the R&S®VSE vector signal explorer software.

03-Feb-2021

This application note describes the general setup and required equipment for EMC measurements according to the EMS standard IEC / EN 61000-4-3.

29-Mar-2007 | AN-No. 1SP32

This application note shows how to perform user equipment (UE) receiver tests, such as block error rate (BLER) and throughput tests, under fading conditions with the R&S®CMW500 RF tester and the R&S®SMW200A vector signal generator in LTE(-A), W-CDMA (HSPA+), TD-SCDMA, GSM (GRPS and EGPRS(2)), CDMA2000 and 1xEV-DO.

03-Nov-2015 | AN-No. 1MA194

To quantify uncertainties for network analyzer measurements, the influence of the entire system (network analyzer plus test setup and DUT) has to be taken into account. Usually, the overall uncertainty of the complete measurement setup is determined with the aid of a verification kit, containing highly accurate verification standards. Of course, the verification standards need to have the same connector type as the DUT. If such verification standards are not available, the overall error has to be estimated.

28-Jul-1998 | AN-No. 1EZ29

Short test times in conjunction with accurate and repeatable measurement results are essential when testing and calibrating mobile phones at board level. The R&S FSP Spectrum Analyzer offers wide dynamic range, stable and accurate results within shortest sweep time, making it the ideal choice for high-volume production testing. The utilisation of both the list mode feature and the marker list function for the Spectrum Analyzer R&S FSP, with its unsurpassed measurement speed via remote control are demonstrated in this application note.

29-Aug-2003 | AN-No. 1MA65

The R&S®SMW200A vector signal generator can take on the role of a powerful and flexible signal generation source for the most realistic and agile radar scenarios in highly integrated radar scenario simulators. Equipped with the R&S®SMW-K503/-K504 options, the R&S®SMW200A can generate any stateof-the-art and future I/Q modulated radar signals from streamed pulse descriptor words (PDW). It supports a PDW execution rate of up to 12 megapulse descriptor words per second (MPDW/s).

20-Nov-2020

The R&S®FSW signal and spectrum analyzer offers fast and easy-to-use transmitter testing for the demanding DOCSIS 3.1 cable modem (CM) and cable modem termination system (CMTS) requirements.

12-Apr-2016

Fokus EMI debugging

24-Jul-2024

Rohde & Schwarz offers a powerful tool for remote control of their oscilloscopes - the RsInstrument Python module. This module enables users to control and automate their Rohde & Schwarz test & measurement instruments, including oscilloscopes, through Python scripts or interactive console communication.

14-Dec-2023

The R&S VSA and R&S UAF video analyzers have been designed for measurements on CCVS signals. Under certain conditions, they can also be used for measuring the primary colour components RGB and TV signals in the S-Video format.

21-Feb-2003 | AN-No. 7BM29E

This application note describes essential test setups and test procedures for 3GPP power amplifiers especially for production lines.

04-Sep-2002 | AN-No. 1MA40

3-Port Adapter ZVR-B8 is an optional accessory to all Vector Network Analyzers of the ZVR family, namely ZVRL, ZVRE, and ZVR, and extends the two test ports PORT1 and PORT2 to a total of three test ports PORT1, PORT2 and PORT3. The option comprises an electronic single-pole double-throw switch (SPDT) by means of which PORT1 of the analyzer is switched to either PORT1 or PORT3 of 3-Port Adapter. Test port PORT2 of the analyzer is directly connected to PORT2 of the 3-Port Adapter and is not switched over.

04-Aug-1998 | AN-No. 1EZ26