Search Application Notes & Cards
Learn how to configure Rohde & Schwarz products to fit your application. Search our database by product, technology, or application to find relevant technical documents.
Search Application Notes & Cards
Learn how to configure Rohde & Schwarz products to fit your application. Search our database by product, technology, or application to find relevant technical documents.
1118 Results
This application note describes Methods of Implementation (MOI) for precise, fast, and error-free compliance testing of USB 3.2 Legacy Cable Testing for USB Type A, Type B, and Micro family connector types. Based on 5 Gbps and 10 Gbps signaling per lane with vector network analyzers from Rohde & Schwarz.
09-Nov-2023 | AN-No. 1SL408
Noise sources used for noise figure and gain measurements are typically controlled by the spectrum analyzer or noise figure meter instruments and are calibrated with their ENR value (Excess noise ratio). While this external control and the use of ENR values is common in noise figure test, it may be difficult in system applications where the noise source control is not available, and the use of ENR values is replaced with the values for the noise output power of the noise source. The calculation of the output power for the noise source requires to know the P_hot value (hot power) which is not a common specification for noise sources used in test and measurement applications.This application note describes a technique to perform a calibrated noise power measurement (P_hot) with spectrum analyzers and noise sources. The next sections will give further details.
31-May-2022 | AN-No. 1EF113
In civil aviation, instrument landing system (ILS) transmitters use antenna arrays to provide guidance to approaching aircraft. ILS performance strongly depends on the precise alignment of the magnitude and phase of each element in an antenna array. The R&S®ZNH handheld vector network analyzer with a built-in source allows fast, convenient on-site measurements on the ILS antenna system.
09-Aug-2021
Describtion and explanation of the MPEG and DVB-Standards and TV T&M
10-Dec-2011 | AN-No. 7BM_ADD01
Embedded power supplies combine traditional power supply components with multiple sensors, processing and control logic as well as digital communications interfaces. Test equipment for debugging requires isolated input channels for measurements of hazardous voltages. Additional digital channels support the analysis of digital signals, while trigger and decode capabilities are essential for time-correlated monitoring of serial protocol-based communications interfaces.
26-Apr-2016
In addition to frequency, power and long-term stability, short-term stability or its equivalent, phase noise, is an important characteristic of signal sources. For example, the phase noise of conversion oscillators of receivers obtained in the presence of a strong signal determines adjacent-channel sensitivity. In the case of transmitters, the phase noise of the oscillator together with the modulator characteristics is responsible for the power generated in adjacent channels. The phase noise of oscillators or synthesizers and the relevant measurements therefore play an important role in radio transmission systems.
16-Jan-2002 | AN-No. 1EF16
This application note describes the general setup and required equipment for EMC measurements according to the EMS standard IEC / EN 61000-4-3.
29-Mar-2007 | AN-No. 1SP32
To quantify uncertainties for network analyzer measurements, the influence of the entire system (network analyzer plus test setup and DUT) has to be taken into account. Usually, the overall uncertainty of the complete measurement setup is determined with the aid of a verification kit, containing highly accurate verification standards. Of course, the verification standards need to have the same connector type as the DUT. If such verification standards are not available, the overall error has to be estimated.
28-Jul-1998 | AN-No. 1EZ29
Harmonic load pull measurements explore potential device efficiency to find the best design topology.
17-Apr-2023
LTE is under continuous development. Release 10 (LTE-Advanced) introduced carrier aggregation (CA) as the primary enhancement. Releases 11 and 12 add several new components to LTE. Some are enhancements to existing features (such as improvements to CA), while others are completely new concepts, such as coordinated multipoint (CoMP).This application note summarizes the Rohde & Schwarz test solutions for LTE-Advanced according to Releases 11 and 12 using vector signal generators, signal and spectrum analyzers and the wideband radio communication tester.
14-Jul-2016 | AN-No. 1MA272
As well as static tests, modern mobile communication standards also stipulate measurements under fading conditions, sometimes with additional white gaussian noise AWGN. Rohde & Schwarz supports these tests with the combination of the R&S®CMU200 Radio Communication Tester and the R&S®SMU200A or R&S®AMU200A Vector / Baseband Signal Generator and Fading Simulator. Applying fading and noise always raises the crest factor of a signal considerably. Thus, automatic path attenuation inside the Rohde & Schwarz baseband fader prevents the new signal peaks from being clipped at I/Q full scale. Any additional attenuation in the baseband, however, makes the RF output fall below its intended level. This application note shows how to achieve an accurate RF output level by compensating for the I/Q attenuation - without modifying the test setup or using additional instruments.
09-Jan-2009 | AN-No. 1MA135
Voice over IP for air traffic control
17-Jun-2013
A turnkey 5G Field-to-Lab solution based on R&S®CMX500
5G New Radio (NR) is the fifth-generation radio interface and radio access technology (RAT) which was officially published by 3GPP in release 15. With the 5G technology, it enters a new era to meet the ever-increasing demands of mobile communications not only in the conventional cellular communication world, but also in the vertical industries.Since the commercialization of 5G NR, worldwide 162 networks have been deployed as per the report of GSA. On the path to the 5G NR network commercialization and service launch, field test is one of the essential user centric processes that User Equipment (UE) vendors should go through. Sophisticated features and versatile deployment options have to be thoroughly checked to ensure the reaching of certain confidence level before the official launch.However, field test is often linked with some challenges, such as► High costs due to the extensive drive tests► Time tedious analysis of a drive test that lowers the efficiency► Lack of test repeatability that makes the regressing tests impossibleWhat if providing an alternative solution in a laboratory environment to cope with all above mentioned challenges during the field test? R&S® as a world-wide well established test measurement equipment manufacturer and solution provider developed a 5G field-to-lab (F2L) turn-key solution, R&S®CM360°. It features► the simulation of the network with the real network configurations to avoid the cost intensive drive test by utilizing mobile radio tester R&S®CMX500► intuitive tools to visualize, drill down the problems and therefore enhance the debugging efficiency based on R&S®SmartAnlytics► the specialized key performance indicator (KPI) tests configured through real network data offered on R&S®CMX500 that guarantee the test reliability and repeatabilityThis application note aims to demonstrate the status of quo R&S®CM360° F2L solution.
16-Jul-2021 | AN-No. 1SL369
This white paper summarizes the technology options for supporting voice and short message service (SMS) in LTE, including circuit switched fallback (CSFB), SMS over SGs, and voice over LTE (VoLTE).
11-May-2011 | AN-No. 1MA197
This Application Note presents a program which combines FM tuner measurements to form automatically running sequences in line with DIN EN60315-4. It is an extension of Application Note 1GA43 and can be used with the Generator R&S SML and the Audio Analyzer R&S UPV or UPL.
15-Dec-2006 | AN-No. RAC-0502-0012
Rohde & Schwarz signal generators can generate standard-compliant WLAN IEEE 802.11ax signals for high efficiency (HE) receiver testing.This application note helps to choose the right generator test solutions and explains step-by-step how to generate 802.11ax SISO and MIMO signals. Measurements, such as EVM, are presented to illustrate the signal performance. Furthermore, this document shows how to test 802.11ax receiver specifications and the newly introduced HE trigger-based PPDU specifications according to the IEEE P802.11ax/D1.3 specification draft.
16-Aug-2017 | AN-No. 1GP115
R&S®CMWcards, an intuitive and user-friendly software application, makes it possible to recreate field testing in a lab environment.
19-Feb-2019
Ethernet communications has been introduced in automotive networks to enable fast and cost efficient data communications, e.g. for the rearward camera or audio/video streaming. In the OPEN alliance (www.openSIG.org), the automotive industry has standardized the BroadR-Reach® physical layer as the automotive Ethernet communications standard. It will be part of the IEEE 802.3 standard. BroadR-Reach® uses full duplex twisted pair communications, enabling 100 Mbit/s data transfer. For interface verification the OPEN Alliance has specified a BroadR-Reach® conformance test with six test cases.
27-Mar-2015
Development of modern EW systems is a complex and expensive process, that requires thorough testing against all requirements during all phases of development. To keep cost under control, system level testing in the lab is key and brings several advantages: test cases can be reproduced under the exact same conditions as often as necessary. System level testing in the lab is often performed in a hardware-in-the-loop (HIL) environment. This application note provides some insight into generating radar signals for hardware-in-the-loop testing with the R&S®SMW200A. An introduction to HIL testing and realtime operation of the R&S®SMW200A is given. The hardware and software interface, the PDW format and synchronization and timing mechanisms are described. Additionally, various example scenarios and detailed information about intermediate calculations are provided. The application note also provides information about system requirements for advanced PDW streaming with multiple emitters on multiple parallel streams.
22-Jan-2021 | AN-No. 1GP124
LLC resonant converters achieve very high efficiency levels due to soft switching. However, during the power-on phase such a converter might behave differently until the controller has reached a steady state. Measuring the inrush current and the power-on time ensures that they are within standards and comply with the data sheet.
29-Nov-2018
This application note describes Methods of Implementation (MOI) for precise, fast, and error-free compliance testing of USB Type-C to legacy cable assemblies supporting USB3.1 Gen2, USB3.1 Gen1, and USB2.0. Based on 5 Gbps signaling per lane with vector network analyzers from Rohde & Schwarz.
18-Jan-2024 | AN-No. 1SL406
This application note describes how to generate 3GPP (UTRA-FDD) signals for receiver tests under fading conditions for user equipment. The test setup requires an R&S®CMU200 Universal Radio Communication Tester with option R&S®CMU-B17 IQ-IF interface and an R&S®SMIQ Vector Signal Generator. The test setup can be calibrated with either a R&S®NRP-Zx USB power sensor or an NRP, NRVD, or NRVS Power Meter. To calibrate the baseband and RF path and configure performance tests according to the 3GPP test specification 34.121 easily, the program 3GFadLevCor is included.
01-Mar-2005 | AN-No. 1MA76
This application note provides basic information about settling time measurements and describes how frequency settling time measurements can be easily and convenient performed using a modern spectrum analyzer with integrated signal analysis capabilities.The analog demodulation measurement application R&S®FSxx-K7 performs frequency and phase settling time measurements using a modern wideband concept, and results are obtained easily and convenient with an integrated settling time measurement capability.
18-Jun-2022 | AN-No. 1EF112
Reliable testing of HARQ feedback and UL timing adjustment on LTE eNBs with the R&S®SMW200A simplifies eNB performance testing and eliminates the need for test UEs
01-Jun-2016
This application note provides information about measurements on pulsed signals with a spectrum analyzer. Examples show the practical realisation of measurements like pulse width, peak power and mean power, and the limitations of spectrum analyzer measurements. A method for long time average power measurement is explained.
16-Jan-2003 | AN-No. 1EF48
The R&S®FPS-K18 amplifier measurement option in combination with the R&S®FPS signal and spectrum analyzer and the R&S®SGT100A SGMA vector RF source enables high-speed amplifier characterization.
13-Jun-2016
RF physical layer specifications (such as 3GPP TS36.104) describe a variety of requirements that the end equipment needs to meet. This application note provides insight into some of these specifications and how test & measurement equipment can simplify the task of deriving requirements for RF sub-systems.
10-Apr-2013 | AN-No. 1MA221
This application note briefly summarizes the history of SCPI and outlines in which fields of application a SCPI based test system software has still advantages over a driver (e.g. IVI) based approach. Further the unique features of the high-end R&SSMW 200A vector signal generator that allow an increase in efficiency of SCPI based test system software development are introduced and operating guidelines are provided.
18-Oct-2017 | AN-No. 1GP98
With continuously increasing data rates, signal integrity in high speed digital designs becomes more and more demanding
08-Jul-2022