Polar modulation is a method where digital modulation is realized as a combination of phase and amplitude modulation, rather than using an I/Q modulator. This technique becomes increasingly important in mobile communication. This application note shows how to generate polar modulation with an R&S®SMU200A Vector Signal Generator.

26-Nov-2004 | AN-No. 1GP58

GSM standard 11.10 prescribes a number of tests requiring measurements on mobile stations under multichannel conditions (fading). The combination of Radiocommunication Tester CRTP02 or CRTC02 and Signal Generator SMIQ allows cost-effective performance of the most important fading tests, in particular the tests according to sections 13.2, 14.2 and 14.3 of GSM 11.10. The aim of this application note is to familiarize the user with all the capabilities offered by the above combination of measuring instruments. The user should then be able to quickly generate and run his own fading tests using the IEC/IEEE-bus control commands described in this application note. To facilitate reading of the following, the testers CRTP02 and CRTC02 are referred to as CRTx.

07-Nov-1997 | AN-No. 1MA02

Sequencer Software Tool

14-Mar-2016

Battery life time is usually one of the most important specifications for battery-powered devices. Depending on the application, life time requirements can range from tens of hours for typical wearables like smart watches to ten years for smart sensors. Understanding where and when energy is used in order to minimize power consumption is therefore key for any of these devices.The power consumption analysis tool was developed to make it easier for customers to analyze power consumption data collected with either the NGL, NGM or NGU power supplies from Rohde & Schwarz. It allows to easily capture power consumption data and analyze using basic measurements.

31-Jan-2022 | AN-No. 1SL380

Distortions caused by components in the RFFE (radio frequency front end) limit the performance and throughput of communications systems. Types of distortions include:▪ AM-AM and AM-PM (complex variations of gain with amplitude)▪ Non-linear frequency response (memory effect)All RFFE components exhibit all of these distortions, only the proportions vary. In this Application Note, illustrative measurements of individual RFFE components, as well as a complete RFFE, will be made. This is followed by the documentation of a more complete analysis, including comparison against theoretical limits, of a linearized commercial SatCom BUC product.

27-Feb-2017 | AN-No. 1MA299

DOCSIS has become the established standard for return channels when it comes to implementing interactive services in broadband cable networks. The quality of these signals is essential to network efficiency. The analysis can be done using the highprecision R&S®ETL, R&S®EFA and R&S®FSH3-TV TV test receivers that have proven themselves in the downstream. These T & M instruments can be quickly and easily configured for measuring the upstream.

13-Jul-2012

Today’s electronic devices often draw non-sinusoidal, irregular current where harmonic current is fed back into the universal supply system. Monitoring this current is both crucial and mandatory for CE compliant devices. The R&S®NPA701 compliance tester seamlessly and efficiently monitors this current.

28-Mar-2024

3GPP TS25.141 defines conformance tests for W-CDMA base stations (including HSPA+ features). This application note describes how all required receiver (Rx) tests (TS25.141 Chapter 7) can be performed easily and quickly by using vector signal generators and CW sources from Rohde & Schwarz. One test additionally requires a spectrum analyzer from Rohde & Schwarz.Example illustrates manual operation. A free software program enables and demonstrates remote operation. The W-CDMA base station transmitter (Tx) tests (TS25.141 Chapter 6) are described in Application Note 1MA67.

21-Oct-2014 | AN-No. 1MA114

The R&S®ZNB vector network analyzer is easy to configure and calibrate using the built-in intermodulation wizard.

19-Dec-2013

This Application Note describes two easy ways of extracting the video content of MPEG-2 transport streams and storing it as video elementary streams. These elementary streams can later be used to generate customized MPEG-2 transport streams by means of the Advanced Stream Combiner R&S DVASC application.

21-Apr-2006 | AN-No. 7BM58

The application note guides developers and manufactures of Sigfox Devices to perform the required and recommended measurements with test solutions from Rohde & Schwarz. The note will help bring ultranarrowband IoT devices and applications using Sigfox technology to the market as fast as possible and help ensure the desired quality and performance.For R&D, Pre-certification and QA, all currently defined Uplink- and Downlink- measurements are shown using the compact R&S®FPL1000 Spectrum Analyzer and R&S®SMBV100A Vector Signal Generator.For Production, use of the R&S®CMW100A Communications Manufacturing Test Set is shown for the most essential Uplink RF tests on Sigfox Devices.Python scripts for giving example SCPI commands demonstrate how measurements shown in manual use can easily be automated.

15-Nov-2017 | AN-No. 1MA294

Automated long-term measurements expand snapshot measurements associated with risk communication

12-Jun-2007

Application Note 1MA104 shows you how to quickly and easily create TD-SCDMA test signals for user equipment and base station tests as stipulated in the standards TS 34.122 and TS 25.142.

10-May-2007 | AN-No. 1MA104

Testing radomes, bumpers, QAR50 Ensure a high level of performance and reduce performance degradation of automotive radar sensors caused by radomes and bumpers with the R&S®QAR50. Testing radomes and bumpers in all phases – from design to high-volume production Testing radomes, bumpers, QAR50 Ensure a high level of performance and reduce performance degradation of automotive radar sensors caused by

21-Apr-2022

EW receivers are tested in the lab at RF to discover problems before flight testing. This eliminates cost and schedule risk. Flight testing can cost tens of thousands of dollars per hour and must be scheduled many months in advance. In contrast, using test equipment to test at RF might require a certain upfront cost but provides a readily-accessible capability to simulate radar threats at RF for a long time. This application note explains how the angle-of-arrival (AoA) capabilities of EW receivers can be tested with commercial off-the-shelf (COTS) RF test equipment. Topics covered are the generation of scenarios, instrument setup, and setup calibration. We will use a radar warning receiver (RWR) as a proxy for a generic EW receiver in this application note.

22-Dec-2021 | AN-No. 1GP125

EMI debugging, FPC, FPC1000, FPC1500, EMC compliance test, EUT The combination of high power and current being sharply switched on and off has a lot of potential for EMI. EMI debugging a switched-mode power supply with R&S®FPC1000/ R&S®FPC1500 EMI debugging, FPC, FPC1000, FPC1500, EMC compliance test, EUT The combination of high power and current being sharply switched on and off has a lot of potential

30-Jun-2019

Rohde & Schwarz presents the R&S®ATS1000 antenna test system, a highly accurate solution for testing 5G antennas up to mmWave frequencies in a mobile shielded chamber.

17-Oct-2017

During development of MU-MIMO antenna arrays, the beamforming algorithms undergo steady revision. Whether used in regression testing or verification of newly introduced features, fast beamforming verification helps to speed up R&D for beamforming antennas and improve performance of your product.

07-Jul-2020

Since June 2017 almost all radio transmitters and receivers sold or put into operation in the European Union have to be tested for immunity against interferers in adjacent frequency bands. ETSI standard EN 303 345 defines the tests to be performed on broadcast sound receivers, and the requirements to be passed.This application note describes the test procedures and provides script files and interferer signals for the Broadcast Test Center R&S®BTC.

29-May-2020 | AN-No. 1GP117

Rohde & Schwarz offers a complete test solution for WiMAX applications by combining its Signal Generator R&S SMU200A and Signal Analyzer R&S FSQ plus the appropriate options. This application note provides an overview of the differences between OFDM and OFDMA and demonstrates, how convenient it is to generate and analyze WiMAX OFDMA signals according to standard IEEE 802.16e-2005.

23-May-2007 | AN-No. 1EF58

Today virtually every electronic device has a standby mode. Power consumption is regulated in most countries by increasingly stringent limits. This makes standardized power measurement essential.

12-Sep-2018

For establishing a WLAN connection between R&S®CMW and device under test (DUT), the WLAN properties at the R&S®CMW have to be adapted to the test conditions. These can vary in several aspects, particularly due to the different WLAN standards and characteristics of the DUT. This document describes the critical parameters and provides step-by-step procedures for the configuration.

08-Dec-2015 | AN-No. 1C106

The R&S® ZVA-Z110 converters offered for the R&S® ZVA family enable network analysis in the W band (75 GHz to 110 GHz). In this Application Note, measurements with three or four converters will be discussed. Test configurations for such measurements have so far been implemented only with coaxial connector systems for a frequency range up to approx. 40 GHz. The term 'multiport measurements' was created for this type of measurements.

09-Oct-2007 | AN-No. 1EZ56

End-to-end conformance testing of 4G and 5G next generation eCall (NG eCall) modules under controlled network conditions

13-May-2024

The IP connection security analysis solution for the R&S®CMW500 platform identifies IP connection vulnerabilities in telematics units at an early stage of development.

18-Jul-2017

New technologies and applications like 6G communications and sensing extend into sub-THz frequencies in the D band and beyond. New semiconductor technologies and processes need to be commercialized to support these efforts.

12-Dec-2023

The R&S®SMW200A vector signal generator has the outstanding ability to simultaneously generate up to eight independent signals from a single instrument. The advanced multi-channel architecture allows realizing even complex applications like MSR, carrier aggregation, MIMO or enhanced interference scenarios with a minimum of effort.This application note gives an overview of common multi-channel application examples and how to equip the Rohde & Schwarz signal generator R&S®SMW200A appropriately.

12-Mar-2018 | AN-No. 1GP106

Voice over IP for air traffic control

21-Nov-2014

Taking the R&S ESR EMI test receiver as an example, this paper looks at a CISPR 16-1-1- compliant test instrument with time domain scanning capabilities. The paper compares the measurement speed and level measurement accuracy of a conventional stepped frequency scan versus an advanced FFT-based time domain scan. It also contains guidance on making optimum use of time domain scans.

29-Jan-2014 | AN-No. 1EE24

For cable TV, the "last mile" to the connection at the home is the bottleneck that prevents higher data rates. The last mile is made up of optical fiber and coaxial cables, amplifiers and electrical/optical converters. This mix of optical fiber and coaxial cables is known as a hybrid fiber coax (HFC) network. One option for cable network providers to maximize both the downstream (DS) and upstream (US) data throughput using the existing cable TV network, but without making expensive changes to the HFC network infrastructure, is to employ the data over cable service interface specification (DOCSIS) 3.1.This Application Note discusses the fundamental technological advances of DOCSIS 3.1 and presents measurement solutions from Rohde & Schwarz.

02-Mar-2015 | AN-No. 7MH89