343 Results
The application note address test and measurement possibilities for DVB-S2 and DVB-S2X signals in the Ku & Ka -band.
08-Mar-2016 | AN-No. 1MA273
Digital pre-distortion (DPD) is a common method. This article describes an approach to generate a pre-distorted signal based on a hard-clipper.
13-Sep-2017 | AN-No. 1EF99
This application note describes how all required receiver (Rx) tests (TS25.141 Chapter 7) can be performed easily and quickly by using vector signal generators and CW sources from Rohde & Schwarz.
21-Oct-2014 | AN-No. 1MA114
This Application Note addresses signal measurements and analysis of automotive radars that are crucial during the development and verification stages.
10-Jun-2016 | AN-No. 1MA267
Hints and Tricks for Remote Control of Spectrum and Network Analyzers
19-Aug-2014 | AN-No. 1EF62
LTE is under continuous development. Release 10 (LTE-Advanced) introduced carrier aggregation (CA) as the primary enhancement. Releases 11 and 12 add several new components to LTE. Some are enhancements to existing features (such as improvements to CA), while others are completely new concepts, such as coordinated multipoint (CoMP).This application note summarizes the Rohde & Schwarz test solutions for LTE-Advanced according to Releases 11 and 12 using vector signal generators, signal and spectrum analyzers and the wideband radio communication tester.
14-Jul-2016 | AN-No. 1MA272
This document provides the technical specifications of the R&S®FSx-K8 Bluetooth® measurement application.
Direct remote control of OSP via VNA and SA
06-Dec-2013 | AN-No. 1MA226
conducted conformance testing according to TS 38.141-1, Rel. 15
This application note describes how all mandatory RF receiver tests can be performed quickly and conveniently with signal generators from Rohde & Schwarz.
02-Dec-2020 | AN-No. GFM314
This application note describes the configuration of a Miracast wireless video transmission system and how to measure delay times.
01-Oct-2015 | AN-No. 1MA250
R&S®Fxx-K40 Phase Noise Measurement Application – R&S®FSW-K40, R&S®FSMR3-K40, R&S®FSV3-K40, R&S®FPS-K40, R&S®FSV-K40, R&S®FPL1-K40 - Specifications
conducted conformance testing according to TS 38.141-1, Rel. 16
This application note describes how all mandatory RF transmitter tests according to Release 16, can be performed with signal or spectrum analyzers from Rohde & Schwarz.
27-Jan-2021 | AN-No. GFM313
radiated conformance testing according to TS 38.141-2, Rel. 16
3GPP defines the Radio Frequency (RF) conformance test methods and requirements for 5G NR Base Stations (BS) in the technical specifications TS 38.141.
30-Jun-2020 | AN-No. GFM325
R&S®VSE-K60(x) / FSW-K60(x) / FSWP-K60(x) / FSV3-K60(x) Transient measurements - Specifications
1MA210 - Testing LTE Release 9 Features. This Application Note describes the T&M methods for LTE Release 9 features using Rohde & Schwarz instruments.
26-Apr-2013 | AN-No. 1MA210
This white paper describes how a QAgent deployment might be handled to lessen the impact on production or lab environments.
This application note summarizes the Rohde &Schwarz test solutions for LTE-Advanced (Release 10) using Vector Signal Generators, Signal and Spectrum Analyzers and the Wideband Radio Communication Tester.
03-Sep-2014 | AN-No. 1MA166
Introduction to Attribute Based Instrument Drivers
01-Dec-2012 | AN-No. 1MA170
04-Jan-2024
Rohde & Schwarz leverages technology from Analog Devices to develop a wireless battery management system production test solutionAnalog Devices, Inc. (ADI) and Rohde & Schwarz are helping the automotive industry to adopt wireless battery management system (wBMS) technology which brings technical, environmental, and cost advantages compared with wired battery management systems (BMS). A new automated test solution is tailored for verification and mass production tests of wireless device tests. This development builds on existing efforts for wBMS RF robustness testing.
This application note aims to explain test procedures and characterization of the relevant parameters for active phased array antennas.
04-Jul-2016 | AN-No. 1MA248
30-Oct-2023
Enabling an AI-native air interface for 6G: Rohde & Schwarz showcases AI/ML-based neural receiver with optimized modulation at Brooklyn 6G Summit, in collaboration with NVIDIARohde & Schwarz and NVIDIA showcase AI/ML-based neural receiver with custom modulation at Brooklyn 6G Summit
Noise Power Ratio Signal Generation and Measurement
Noise Power Ratio is a tool for WinIQSIM™ to generate noise power ratio stimulus signals and measure the resulting noise power ratio of a device.
06-Nov-2015 | AN-No. 1MA29
Assisting Tools for Operation of Windows-Based T&M Instruments
13-Jun-2013 | AN-No. 1MA218
This application note describes how all required transmitter (Tx) tests can be performed quickly and easily by using signal and spectrum analyzers.
11-May-2016 | AN-No. 1MA154
05-Sep-2023
Rohde & Schwarz and Greenerwave collaborate to verify RIS modules and drive 6G researchReconfigurable intelligent surfaces (RIS) can revolutionize wireless communication performance for 5G and future 6G applications. A groundbreaking measurement campaign by Rohde & Schwarz and Greenerwave confirms the capabilities of a novel FR2 RIS module, improving coverage and efficiency.
Amplifier measurements with Rohde & Schwarz spectrum analyzers Flyer
This document describes how a Windows®-based R&S® T&M instrument is remotely operated by an Apple iPad as if working on it locally.
28-Mar-2013 | AN-No. 1MA216
30-Aug-2023
Rohde & Schwarz showcases its latest mmWave test solutions at the European Microwave Week in BerlinJoin Rohde & Schwarz in Berlin for EuMW 2023, Europe's premier microwave event! Discover cutting-edge test solutions focused on early sub-THz research for 6G.
Rohde & Schwarz User Manual for the R&S®FSW-K76/-K77 TD-SCDMA applications; provides all the information specific to the application. All general instrument functions and settings common to all applications are described in the main R&S FSW User Manual.
Rohde & Schwarz User Manual for the R&S®FSW-K72/-K73 3GPP FDD applications; provides all the information specific to the application. All general instrument functions and settings common to all applications are described in the main R&S FSW User Manual.