156 Results
How do I calculate these frequency points when I have a logarithmic sweep and know the center frequency, the span and the number of sweep points?
I have used my TRL calibration kit with my ZVA before. Now I want to use also with my ZNB. But when I try to load the data of the calibration kit into the ZNB, the above error message is shown.
TDR, TDT, ZVA vector network analyzer, This video series demonstrates the calibration of a four-port network analyzer and the measurement of rise time, impedance vs. distance and skew on a board with differential lines.
TDR, TDT, ZVA vector network analyzer, This video series demonstrates the calibration of a four-port network analyzer and the measurement of rise time, impedance vs. distance and skew on a board with differential lines.
TDR, TDT, ZVA vector network analyzer This video series demonstrates the calibration of a four-port network analyzer and the measurement of rise time, impedance vs. distance and skew on a board with differential lines.
The R&S®ZVA vector network analyzer in combination with the R&S®ZVAB-K30 noise figure measurement option simplifies noise figure measurement, a key parameter for receiver performance evaluation.
This application note describes how to configure a Rohde & Schwarz Network Analyzer to make spectral measurements directly on a device under test.
16-Mar-2012 | AN-No. 1EZ62
ZVA Vector Network Analyzers, PIM, Rohde & Schwarz demonstrated fast and accurate passive intermodulation (PIM) testing of duplex filters at the European Microwave Week 2013 in Nuremberg.
This application note describes the techniques to measure the dielectric properties of materials using a vector network analyzer. It also shows methods for converting the s-parameters to dielectric properties.
23-May-2012 | AN-No. RAC-0607-0019
I want to use Port 1 and Port 3, so I tried to switch them on by setting the value to 1 (the default value) and to switch off Port 2 and Port 4 by setting the value to 0. But this does not work. How do I set the ports?
This paper shows how to perform a n-port multi-port calibration by using calibration unit with a lower number of ports than available of the vector network analyzer.
06-Feb-2013 | AN-No. 1EZ70
This document describes how a Windows®-based R&S® T&M instrument is remotely operated by an Android™ tablet as if working on it locally.
22-Aug-2013 | AN-No. 1MA236
Russian version - Измерения в диапазоне миллиметровых волн с использованием преобразователей семейства R&S®ZVA
Russian version - Измерение S22 усилителя в «горячем» режиме с импульсными сигналами на анализаторе цепей R&S®ZVA
This application note explains how to generate phase coherent signals with a compact easy-to-use solution.
07-Sep-2016 | AN-No. 1GP108
This application note along with its corresponding white paper 1MA207 show how to use the R&S radar product portfolio to tackle test and measurement tasks in modern radar technology.
10-Aug-2012 | AN-No. 1MA127
Inside the lab and on the production line – this Rohde & Schwarz solution offers speed, accuracy and convenience for testing TX beamforming passive array antennas.
04-May-2018
This document provides an introduction to SDR as used for military radios and presents the relevant T&M solutions offered by Rohde & Schwarz.
15-Sep-2012 | AN-No. 1MA206
This document provides the technical specifications of the R&S®ZCxxx millimeterwave converters.
Fault identification in single elements of antenna arrays is possible by scanning in near-field range and applying the near-field to far-field transformation method.
24-Mar-2020
RPG ZRXxxx Millimeterwave Receiver - Specifications
R&S®Forum for Instrument Remote Control
28-Jun-2018 | AN-No. 1MA196
Testing TRM performance of modern AESA antennas - Flyer
This application note outlines two different approaches for remote-controlling Rohde & Schwarz instruments out of MathWorks MATLAB.
12-Jun-2017 | AN-No. 1MA171
Development Hints and Best Practices for Using Instrument Drivers
01-Jan-2013 | AN-No. 1MA153
This application note reviews a new calibration subsystem which consists of Inline Calibration Units (ICUs). These ICUs are designed for in situ use, so they are left in place both during the calibration procedure and during the measurement of the Device Under Test (DUT).This adds versatility, convenience and accuracy to the VNA based measurement system, as it means the calibration can be refreshed at any time without manually disconnecting the DUT from the test system.
29-Sep-2017 | AN-No. 1EZ71
R&S®VISA is a standardized software library that allows fast communications over diverse interfaces with a wide variety of T&M instruments that are detected on the network from PC applications.
26-May-2020 | AN-No. 1DC02