77 Results
Analog and digital audio measurements with the R&S CMW.
20-Jun-2013
Functionality testing of automotive infotainment devices - Application Card
19-Feb-2018
Conducted multistandard in-device coexistence testing - ApplicationCard
19-Feb-2018
This document describes the critical parameters and provides step-by-step procedures for the configuration.
08-Dec-2015 | AN-No. 1C106
R&S<sup>®</sup>CMW500 Digital IQ with CADENCE Emulator
30-Jun-2011 | AN-No. 1CM75
This application note and associated application software may be used to conduct psychoacoustic speech quality evaluation for Voice over LTE (VoLTE) connections. The measurements are based on recommendations ITU-T P.862 and ITU-T P.863. The included software sequence performs decoder/encoder calibration, connection setup for the UE under test and subsequent speech quality analysis.
21-Feb-2014 | AN-No. 1MA204
This application note gives the guidance of how to perform the BLE 5.1 DF RF tests according to the RF test specification of BT 5.1 by using the Rohde & Schwarz test solutions.
30-Oct-2019 | AN-No. GFM327
This document describes the direct test mode mechanisms for testing Bluetooth Low Energy devices and explains how the direct test mode connection is established. The R&S CMW uses a USB port for the direct test mode connection while the Equipment under Test (EUT) may provide a USB port, a serial port or even a 2-wire UART interface for this purpose. Installing or assigning the right driver for the EUT is the main configuration task on the R&S CMW. For EUTs with USB port, the R&S CMW provides a Bluetooth Low Energy USB driver which has to be assigned to the connected EUT.
14-Dec-2016 | AN-No. 1C105
This application note describes how to use the LTE Frequency Division Duplex (FDD) and Time Division Duplex (TDD) measurement functionality provided by the R&S®CMW500 wideband radio communication tester to perform LTE transmitter and receiver measurements.
17-May-2013 | AN-No. 1CM94
It is extremely important to test the application level functional performance of home automation products in the presence of interference.
11-May-2020
R&S CMWrun Sequencer Software Tool
20-Feb-2015
The intuitive graphical user interface makes it simple for users to test wireless devices for compliance with the 3GPP protocols for various technologies.
20-Feb-2015
This application note explains battery life tests using RT-ZVC in combination with CMWrun and CMW500, including example applications.
17-Feb-2017 | AN-No. 1MA281
R&S CMWrun - RF preconformance testing solution
20-Feb-2015
This document describes the adaptive frequency hopping mechanism for improved signaling performance in Bluetooth Basic Rate and Enhanced Data Rate devices.The R&S CMW provides this feature for remote operation in TX, Loopback and Connection test mode. Thereby the R&S CMW acts as a master, while the Equipment under Test (EUT) represents the slave(s) of the piconet.
14-Dec-2016 | AN-No. 1C108
Cell search and cell selection in UMTS LTE
17-Sep-2009 | AN-No. 1MA150
LTE user equipment (UE) receiver performance has significant impact to cellular radio network coverage and capacity. It determines the maximum data throughput across the air interface between the LTE base station (eNB, evolved node B) and the mobile network subscriber UE, thus it determines the total capacity across the air interface. Therefore, it is one of the most important measurements to verify the actual receiver performance of individual devices, and a key metric to compare different devices, in particular.This paper shall give an introduction to receiver performance measurements and discusses the measurement metrics as well as the challenges of over the air (OTA) measurements.
31-Aug-2017 | AN-No. 1ST001
Increase the IP connection security of your IoT device
04-Apr-2017
R&S CMWrun - Turnkey solutions for production
14-Mar-2016
R&S CMWrun - Audio performance testing solution
20-Feb-2015
Modern communications devices support a large number of standards in a very small space, which can lead to interference due to occupying the same frequency bands.
14-Mar-2016
LTE is under continuous development. Release 10 (LTE-Advanced) introduced carrier aggregation (CA) as the primary enhancement. Releases 11 and 12 add several new components to LTE. Some are enhancements to existing features (such as improvements to CA), while others are completely new concepts, such as coordinated multipoint (CoMP).This application note summarizes the Rohde & Schwarz test solutions for LTE-Advanced according to Releases 11 and 12 using vector signal generators, signal and spectrum analyzers and the wideband radio communication tester.
14-Jul-2016 | AN-No. 1MA272
Air Traffic Control (ATC) radar, military Air Traffic Surveillance (ATS) radar and meteorological radar operate in S-Band frequency range. In fact 4G communication systems such as Long Term Evolution (LTE) make also use of these frequencies.
28-Mar-2014 | AN-No. 1MA211
The R&S®CMW wireless communication tester are ideal for designing and verifying Bluetooth® Low Energy (LE) circuits and modules.
27-Jan-2017
his application note briefly describes the technology behind ERA-GLONASS and presents conformance tests for ERAGLONASS using the R&S®CMW500 RF tester and the R&S®SMBV100A vector signal generator.
24-Jan-2018 | AN-No. 1MA251