1804 Results
The packet-switched architecture of LTE does not support circuit-switched voice calls as used in 2G/3G networks. The packet-switched architecture of LTE does not support circuit-switched voice calls as used in 2G/3G networks. Rollout of commercial LTE networks has been ongoing since the end of 2009 and a solution is needed to ensure fully interoperable and globally available voice services.
Two R&S ETL TV analyzers or two R&S ETC compact TV analyzers are used to measure the receive level of a car antenna against that of a reference antenna. The R&S BCDRIVE broadcast drive test software exports measured data for display in Google Earth.
19-Feb-2015
Simple and easy setup to perform precise pulse measurement for maintenance and troubleshooting of radar system by using R&S®Spectrum Rider FPH and with Rohde & Schwarz wideband power sensor. Simple and easy setup to perform precise pulse measurement for maintenance and troubleshooting of radar system by using R&S®Spectrum Rider FPH and with Rohde & Schwarz wideband power sensor.
This video demonstrates the ease of radome and bumper analysis using the R&S®QAR.
Expert Talk Oscilloscope: I²C bus decoding How to identify and trace down errors in I²C interfaces using the Hardware Trigger together with History Mode. How to identify and trace down errors in I²C interfaces using the Hardware Trigger together with History Mode.
This application note focuses on coaxial connectors found in RF and microwave applications, providing general information on the available types.
09-Apr-2015 | AN-No. 1MA99
MXO 4 - See the difference This video shows you how you can better place and stabilize your probes using the the Rohde & Schwarz 2D positioner for passive probes and the 3D positioner for other probes. This video shows you how you can better place and stabilize your probes using the the Rohde & Schwarz 2D positioner for passive probes and the 3D positioner for other probes.
The R&S®HA-Z24E External Preamplifier Manual describes how to set up the preamplifier, how to read out the s-parameters using the provided software, and how to insert the preampifier in a measurement setup. It also includes safety information and a performance test to check the preamplifier's performance.
Program for Measurement Uncertainty Analysis with Rohde & Schwarz Power Meters
26-Jul-2001 | AN-No. 1GP43
Modern, capacitive touchscreens as used, for example, in mobile phones are susceptible to common mode noise exhibited by external power supplies (EPS).
17-May-2018
Generating models with a VNA and using these on an oscilloscope via the deembedding
23-May-2023 | AN-No. 1SL393
This Application Note describes the differences in intermodulation distortion measurements between traditional spectrum analyzers with analog narrow-band IF signal path and modern spectrum analyzers using a wide-band IF signal path and digital RBW filters.
02-Jul-2012 | AN-No. 1EF79
The R&S®ZNA vector network analyzer with integrated LO output and direct IF input options is a simple, cost-effective solution for 2-port and 4-port measurements using Rohde & Schwarz mmWave converters.
19-Jul-2021
This application note explains how to test your remote radio head with Rohde & Schwarz test and measurement equipment.
05-Aug-2013 | AN-No. 1GP78
In this paper we will review the basics of spurious measurements and how the parameters used can affect the detection performance.
14-Jul-2017 | AN-No. 1EF97
I perform a calibration with remote commands. With the command to start the calibration sweep with a short standard I get this error message. What is the problem?
This video presents how to create simple pulse sequences by using repetitions and loops together with pulses with R&S®SMW200A and R&S®Pulse Sequencer software. This video presents how to create simple pulse sequences by using repetitions and loops together with pulses with R&S®SMW200A and R&S®Pulse Sequencer software.
A closer look at phase resolution and practical demonstration using cut outs is included.
Monitoring on up to 10 000 channels with different parameter settings
13-Jul-2012
Rohde & Schwarz application sheet on the significance and effects of the Bit Error Rate (BER) parameter for signal analysis, in particular using the R&S FSW-K70 application
Tackling the Challenges of Pulsed Signal Measurements
18-Jan-2008 | AN-No. 1MA124
Calibrating the CMD Output Level for BER
10-Mar-2000 | AN-No. 1MA24
In this document we will describe in detail how to configure and perform path calibrations with AMS32-K81 in an ATS1500C, using an AREG800A.
03-May-2023 | AN-No. 1SL399
This application note provides information on how to perform spectral emission measurements on pulsed signals with spectrum analyzers using RBW filters.
06-Jun-2019 | AN-No. 1EF106
This application note describes how to determine the uncertainty bounds for a given artificial network impedance for an estimate of the combined standard measurement uncertainty using the Rohde & Schwarz Software “AN Impedance Uncertainty Contribution”.
17-Dec-2010 | AN-No. 1EE23
22-Mar-2022
Rohde & Schwarz Oscilloscope Days return for 2022This live two-day online event will feature application-oriented presentations from Rohde & Schwarz and partners, based on the day to day challenges electronics engineers face when using oscilloscopes and related test and measurement equipment to achieve their testing goals.
This webinar gives an overview of HF propagation, the technical principles underlying NVIS, the different types of antennas commonly used for NVIS operation, as well as the technical and operational aspects of NVIS This webinar gives an overview of HF propagation, the technical principles underlying NVIS, the different types of antennas commonly used for NVIS operation, as well as the technical and
The video demonstrates high frequency signal generation and analysis using signal generator and analyzer solutions from Rohde & Schwarz. How does Rohde & Schwarz support 5G research activities at cmWave and mmWave frequencies? The video demonstrates high frequency signal generation and analysis using signal generator and analyzer solutions from Rohde & Schwarz.
This video shows how to measure the phase noise of a frequency drifting DUT using the IQ/FFT mode of the R&S®FSV3-K40 phase noise measurement option.