1804 Results
Direct remote control of OSP via VNA and SA
06-Dec-2013 | AN-No. 1MA226
This application note provides basic information about the concept of a group delay measurement with spectrum analyzers and signal generators, and how this method simplifies the test setup and improves the measurement speed
09-Aug-2017 | AN-No. 1EF98
This application note describes the tests commonly used during the production of Femtocells, focusing on WCDMA, HSPA, and HSPA+ technology.
02-Feb-2012 | AN-No. 1MA139
In this application note we explain how to test FPGA-based hardware emulators using Rohde & Schwarz vector signal generators for creating suitable real-time test signals at reduced sample rates. We further explain how to correctly adapt AWGN signal generation and fading simulation for “slow I/Q”.
10-Dec-2012 | AN-No. 1GP95
This application note describes how all required receiver (Rx) tests (TS25.141 Chapter 7) can be performed easily and quickly by using vector signal generators and CW sources from Rohde & Schwarz.
21-Oct-2014 | AN-No. 1MA114
This application note describes how to generate and analyze wideband digitally modulated signals in the mm-wave range. Rohde & Schwarz measuring equipment and some 3rd party off-the-shelf accessories are used for both signal generation and analysis.
02-Sep-2014 | AN-No. 1MA217
Testing S-Parameters on Pulsed Radar Power Amplifier Modules
11-Apr-2013 | AN-No. 1MA126
How it is possible to generate WLAN signals according to different standards using the SMW200A? Find out in this FAQ.
Analysis of DOCSIS upstream signals from selected cable modems in live cable networks using the unique dynamic upstream analysis function. Analysis of DOCSIS upstream signals from selected cable modems in live cable networks using the unique dynamic upstream analysis function.
It must be able to generate and analyze audio waveforms using the latest methodologies according to PESQ or POLQA, whereby POLQA is used for audio quality measurements during VoNR and VoLTE calls. To do so, the R&S®CMW500 & R&S®CMX500 setup can be extended by an audio analyzer.
Bluetooth Reciver Intermodulaton- and Blocking Performance tests fail with every DUT when using an external signal generator to generate the interferer signals.
How can I switch between the input impedance of 50 Ohm and 1 MOhm by using SCPI command.
I made some power measurements using my R&S RTA4004 that lead to questionable power results. What can I do to improve my results?
I want to set the acquisition mode to Average + HR using SCPI commands. But I can not find the right command in the manual.
How can I add a attenuation table to my cable, used in my measurement setup?
and Impedance Analyzers from Rohde & Schwarz are ideal for measuring impedance at a fixed frequency as well as for determining the best operating point for the component under test The LCR Meters and Impedance Analyzers from Rohde & Schwarz are ideal for measuring impedance at a fixed frequency as well as for determining the best operating point for the component under test Impedance Measurements using
RF signal analysis using VSE with your scope. This video shows how the R&S®RTO oscilloscope with its vector signal explorer (VSE) software can be used to analyze wide band pulsed RF signals in terms of frequency, phase, amplitude and timing.
Using network analyzers to measure fluids, gels and solids - White Paper
R&S®PACE 2 uses deep packet inspection technology together with a comprehensive toolbox of methodologies such as atomic pattern matching, heuristics and behavioral analysis to reliably detect in realtime even encrypted and actively hiding applications and protocols.
Next Generation eCall uses LTE and IMS for an emergency call. The R&S®CMW500 radio communication tester emulates an LTE network with integrated IMS server. Equipped with the R&S®CMW-KA096 test software enables to test NG eCall-capable in-vehicle systems.
A sinus signal with i.e. 10 V peak-peak, frequency 1 MHz is applied. If I choose a vertical scale which is too small the peaks of the waveform are not displayed as they are out of range. Now I activate the digital filter in the “Vertical” menu à “Channel”. The frequency of the filter is also set to 1 MHz. Now even at very small vertical scales (i.e. 50 mV/div) the waveform is displayed completely, see screenshot. But the amplitude can not be correct. What goes wrong here?
22-Oct-2019
R&S®Cloud Protector by Rohde & Schwarz Cybersecurity receives international Security AwardComputing Security Awards 2019: R&S®Cloud Protector security solution wins category "New Cloud Delivered Solution of the Year".
This application note explains battery life tests using RT-ZVC in combination with CMWrun and CMW500, including example applications.
17-Feb-2017 | AN-No. 1MA281
Simulation of DVB-T Channel for Antenna Diversity Reception
31-Jul-2003 | AN-No. 7BM06
RF Level Measurement Uncertainties with the Measuring Receiver R&S FSMR
28-Mar-2006 | AN-No. 1MA92
This application note describes how all required performance tests can be performed quickly and easily by using vector signal generators.
11-May-2016 | AN-No. 1MA162
19-Feb-2020
Rohde & Schwarz and Decawave cooperate to develop T&M capabilities for Ultra Wideband technologiesRohde & Schwarz and Decawave demonstrate test functions for the new generation of Decawave UWB devices with the new generation of Rohde & Schwarz radio communication tester, the R&S CMP200. With this solution, both companies address manufacturers planning wireless devices using Ultra Wideband (UWB) technology to provide secure location-based services.
Rohde & Schwarz Manual for SMA adaptor R&S®RT-ZF7A.
How to setup the Hameg HMP2000 and 4000 Series for TCP/IP RAW socket connection using NI VISA
When using the HMF 25xx the output impedance can be changed. Is it really switched electronically or is it solved by the mathematic way?