Ready to push boundaries in the H band? Discover how you can extend the frequency range of your signal and spectrum analyzers to 220-330 GHz with Rohde & Schwarz.
#ThinkSix: Which new spectrum for 6G? A practical review
Based on a need for available spectrum and experiment licenses, this video explains the reasons for candidate frequencies for fundamental 6G research in the D band (110-170 GHz) and G band (140-220 GHz).
High frequencies completely new to mobile radio mean that researching channel characteristics to determine the effects on transmitted signals of propogation delays resulting from reflection, and losses due to scattering, are a major requirement for 6G research. In this video we demonstrate a test setup for channel sounding in the D-band.
Easy and optimized EVM measurement of 5G NR signals
EVM is an important figure of merit when testing DUTs. Customers expect test equipment to deliver excellent EVM performance out of the box, without the need for extensive configuration and calibration procedures.
In this video we show how to perform the Signal Quality Indicator (SQI) test requirement for the OPEN Alliance TC12 Interoperability test with 1000BASE-T1.
Test certification experts IB-Lenhardt & Rohde & Schwarz
Automotive radar sensors are used in complex and safety-critical applications such as advanced driver-assistance systems (ADAS). Therefore, their correct function and compliance with relevant regulations, must be verified. Watch this short video to find out how IB-Lenhardt conduct this important service with the help of Rohde & Schwarz.
R&S®SMW200A - RF Ports Alignment - Getting Started
This video shows how to set up R&S®SMW200A vector signal generators and use the RF Ports Alignment option SMW-K545 together with the RFPAL PC software to generate multiple signals that are aligned in amplitude, delay and phase at the input of a multi-port DUT.
Angle of Arrival Simulation for Multi-Channel Receivers
This video shows how to define a Direction Finding scenario in the R&S®Pulse Sequencer software and how to replay the scenario on a 4 channel R&S®SMW200A setup that has been aligned in terms of amplitude, delay and phase.
#ThinkSix – Spectrum for 5G, Beyond 5G and 6G research
Rohde & Schwarz video analyzing the regulatory landscape for the spectrum beyond 100 GHz, as well as D-Band, supporting frequencies from 110 to 170 GHz.
Rohde & Schwarz presents a unique solution for OTA tests on 5G NR base stations in the FR2 range. The new R&S®FE44 frontend modules support up-/downconversion of lower-frequency IF signals to RF.
Rohde & Schwarz presents cross-channel measurements up to 4x4 MIMO on 5G transmissions in the FR1 range for the development and verification of 5G base stations and small cells.
The video shows the generation and analysis of a 5G NR TM3.1 test model based on the R&S®SMW200A vector signal generator and R&S®FSW signal and spectrum analyzer.
The video demonstrates how to quickly verify components with different important 5G NR physical layer parameters using the 5G NR generation and analysis options of the R&S SMW200A vector signal generator and the R&S FSW signal and spectrum analyzer.
In this video, we demonstrate the multi-baseband capability of the R&S SMW200A vector signal generator to generate the wanted and the interfering signals for FR2 in one instrument.
The first episode of a new video series will take a look at where 5G is today, explore the unique challenges for test and measurement and discover innovative solutions such as the R&S CMX500 radio communication tester.
NPR is core measurement within the satellite industry used to measure the linearity of an active component or full transmission path or channel within a satellite communication link.
Demystifying 5G – Concept of SSB beamforming in mmWave frequencies
The video explains the concept of synchronization signal blocks (SSB), how SSB beamforming works in sub 6 GHz and mmWave frequencies and how many different beams can be realized by the network infrastructure.
Demystifying 5G – Simultaneous coverage measurements on LTE and 5G NR at 28 GHz
The video demonstrates the simultaneous measurement of 5G NR signals in the mmWave frequency range at 28 GHz and LTE in sub 6 GHz using a single network scanner in a 5G backpack for coverage and beamforming tests.
The video provides insights into the channel raster and synchronization raster in 5G NR in order to explain how to perform coverage measurements for 5G non-standalone and standalone mode.
High-End GNSS simulation with the R&S®SMW200A - Episode 6
This video shows how to perform advanced interferer simulations for testing multi-antenna GNSS receivers with anti-jam capabilities, also known as Controlled Reception Pattern Antennas (CRPAs).
High-End GNSS simulation with the R&S®SMW200A - Episode 5
The performance of GNSS receivers must be validated and characterized not only under ideal conditions, but also in the presence of other communication signals like GSM, UTMS or LTE.
This webinar discusses the test requirements of next generation single-channel and multichannel digital receivers and demonstrates an efficient and comprehensive test solution based on the R&S®Pulse Sequencer software in combination with the R&S®SMW200A vector signal generator.
Testing LTE-U capable eNodeB with R&S®SMW200A and R&S®FSW
This video explains the LTE-U technology and demonstrates how to efficiently measure LTE signals in the 5 GHz unlicensed band on eNodeBs using the R&S®SMW200A vector signal generator and the R&S®FSW signal and spectrum analyzer from Rohde & Schwarz.
High-End GNSS simulation with the R&S®SMW200A - Episode 3
In this third video of R&S’s new video series on high-end GNSS testing, it is shown how to set up a multi-constellation, multi-frequency GNSS scenario and feed the GNSS signals to a connected GNSS receiver.
High-End GNSS simulation with the R&S®SMW200A - Episode 2
In this second video of R&S’s new video series on high-end GNSS testing, it is shown how to work with the instrument, followed by a quick user interface tour introducing the most important configuration options and simulation monitoring features.
High-End GNSS simulation with the R&S®SMW200A - Introduction
This video introduces a new series of videos covering the new R&S®SMW200A GNSS simulator. A general discussion of today’s GNSS testing needs is followed by an overview of key features and possible GNSS configurations for the R&S®SMW200A.
Higher order MIMO testing - 4x4 channel simulation demonstration
Highly developed standards such as LTE and WLAN 802.11ac presuppose MIMO. MIMO testing requires a signal generator with multipath and standard-compliant fading simulation in all signal paths. The R&S®SMW200A vector signal generator can internally simulate all MIMO constellations up to 8x2, including fading.
Webinar: Advanced multi-emitter radar simulation with off-the-shelf T&M equipment
Test scenarios can range from simple pulses for component tests to full scale testing of complex radar systems. Examples show how to map real signal environments with multiple emitters and interferers into vector signal generators to stimulate a system under test.
The R&S®SMW200A vector signal generator is the ideal tool for generating the high-quality, complex digitally modulated signals required for the development of new wideband communications systems or the verification of 3G and 4G base stations.
