1459 Risultati
Mar 08, 2022
Bulgarian Communications Regulations Commission once again puts its trust in Rohde & SchwarzAfter finishing a complete network upgrade to the latest R&S ARGUS 6.1 spectrum monitoring software, the Bulgarian Communications Regulation Commission (CRC) has recently awarded Rohde & Schwarz a follow-up contract for R&S UMS300 compact monitoring and radiolocation systems. The new systems fully comply with ITU recommendations and only require minimal infrastructure.
PACE2 NAT/Mobile Tethering Transparency Plug-in Enterprise - Flyer
Using WEB Control with the FSW seems to be using ports - which port settings are needed?
Using telnet for remote control in WIN10
The measurement range does not fit using a sensor
Calibrating a clamp and creating a transducer table using the R&S ELEKTRA signal path calibration utility
When I connect my device via the USB interface, the internet connection of my PC gets lost.
Due to the lack of a 6G standard, we showcase a 5G NR PUSCH multi-user MIMO scenario, emulating two users with 2x2 MIMO, that are independently faded to simulate realistic channel conditions using the R&S SMW200A vector signal generator. The signal is captured using the MSR4 satellite receiver and transferred to a server.
I would like to do a Reference Calibration using ELEKTRA and Field Probe. For this I have to do Reference Calibrations at 16 positions, this does mean my Field Probe have to be set to each of the 16 predefined points. I set the probe positions manually, so an error can occur by mistake. Is it possible to repeat a measurement for a sensor position, if needed?
HMF2525 / HMF2550 - Using burst mode with infinite repetition HMF2550, HMF2525, burst mode, infinite repetition HMF2525 / HMF2550 - Using burst mode with infinite repetition HMF2550, HMF2525, burst mode, infinite repetition Related Products
How to install multiple version of ELEKTRA.
How can the transducer be imported from Excel into the InstrumentView software?
How can I query the waveform data of the serveral segments?
The student team from Cellsius Project H2 uses an R&S®RTA4004 oscilloscope to validate the functionality of its inverter.
Read this educational note and dive into the discussion about the six most important transformer measurements: turns ratio, mutual inductance, phase angle, primary and secondary inductance, leakage inductance, and interwinding capacitance.
Feb 28, 2024
I perform a calibration with remote commands. With the command to start the calibration sweep with a short standard I get this error message. What is the problem?
The student team from Cellsius Project H2 uses an R&S®RTA4004 oscilloscope to validate the functionality of its inverter.
This application note addresses the diverse possibilities of interoperability between Rohde & Schwarz power sensors and Rohde & Schwarz signal generators. All current and many legacy Rohde & Schwarz signal generators offer the capability of directly connecting power sensors. This enables power measurements without the need of a base unit or separate PC to display the readings. Furthermore, sensors can be used for special tasks like filling a user correction table or continuously controlling levels at crucial points in the measurement configuration.
Aug 31, 2023 | AN-No. 1GP141
The overall concept is explained using a product demo of a 5G TSN juggler which shows a deterministic low latency communication via 5G and ethernet using time sensitive networking(TSN).
The power consumption analysis tool was developed to make it easier for customers to analyze power consumption data collected with either the NGL, NGM or NGU power supplies from Rohde & Schwarz. It allows to easily capture power consumption data and analyze using basic measurements.
Jan 31, 2022 | AN-No. 1SL380
In the satellite sector, components, subsystems and entire satellites must be qualified in a thermal vacuum chamber before they can be used in space. This qualification proves that equipment can not only survive but also function in the harsh conditions encountered during launch and in space.
Oct 05, 2022
This R&S®FSW-K70 application sheet describes the challenge of determining typical signal parameters of an unknown signal from the results of a basic measurement using the R&S FSW VSA application.
Generating models with a VNA and using these on an oscilloscope via the deembedding
May 23, 2023 | AN-No. 1SL393
In this document we will describe in detail how to configure and perform path calibrations with AMS32-K81 in an ATS1500C, using an AREG800A.
May 03, 2023 | AN-No. 1SL399
This video demonstrates the speed, safety and privacy features of the Rohde & Schwarz Quick Personnel Security Scanner and explains the millimeter wave radio technology it uses. QPS demo video Enhanced Technology Solutions for Evolving Security Challenges
MXO 4 - See the difference This video shows you how you can better place and stabilize your probes using the the Rohde & Schwarz 2D positioner for passive probes and the 3D positioner for other probes. This video shows you how you can better place and stabilize your probes using the the Rohde & Schwarz 2D positioner for passive probes and the 3D positioner for other probes.
The R&S®HA-Z24E External Preamplifier Manual describes how to set up the preamplifier, how to read out the s-parameters using the provided software, and how to insert the preampifier in a measurement setup. It also includes safety information and a performance test to check the preamplifier's performance.
Setting up complex real-time trigger conditions using the R&S®RTE and R&S®RTO oscilloscopes increases the test coverage and robustness of converter and inverter systems.
Aug 10, 2020
MIPI D-PHY is a low-power, cost-effective physical layer interface, essential in mobile devices and advanced technology systems. It's a high-speed, source-synchronous interface used in smartphone cameras, smartwatch displays, drones, in-car entertainment, automobile cameras, and radar sensors. This application note explores MIPI D-PHY's features, functionality, and testing practices for device compliance, addressing common issues. It highlights Rohde & Schwarz's equipment for ensuring compatibility and solving issues with MIPI D-PHY, aligned with MIPI D-PHY specification version 2.5.Developed by the MIPI Alliance, D-PHY connects cameras and displays to a host processor via CSI-2 or DSI protocols. It features a master-slave, asymmetrical design for reduced link complexity. Key aspects include a unidirectional clock, optional data signal directions, different data rates for half-duplex operation, point-to-point communication, and high-speed (HS) and low-power (LP) modes for data transfer and battery preservation. In HS mode, D-PHY uses differential signaling with specific impedance, while in LP mode, it operates in a single-ended manner with high impedance termination.The application note from Rohde & Schwarz provides insights into characterizing and debugging MIPI D-PHY, offering conformance verification with MIPI Alliance standards and protocol decoding options.
Jan 31, 2024 | AN-No. 1SL410
A closer look at phase resolution and practical demonstration using cut outs is included.