124 Resultados
EMC32: con desfase de ángulo para el segundo mástil de antena
Inicialice el generador de RF, cambie el nivel de inicio de las pruebas de inmunidad mediante EMC32
FAQ; ¿Por qué veo solo una tabla de resultados en el explorador de EMC32 aunque tengo configurados dos detectores?
EMC32: ¿cómo hace referencia el informe estándar a las medidas en las cámaras semianecoicas?
FAQ; Cada vez que inicio EMC32, aparece un error extraño: "ikey for AMS32 could not be found". ¿Qué debo hacer?
EMC32: Interactive data reduction, difference between "After data reduction" and "Before final measurements".
After calibration I received updated attenuation and transducer tables. How do I enter these values into the EMC32 Explorer to continue new Tests with these values?
R&S EMC32-K27 Dual Receiver Measurement (DRM) - Flyer
Averigüe cómo solucionar el problema si en la rutina general de inicio de EMC32 se muestra el mensaje «Application will be closed» (la aplicación se cierra).
So far I only have experience how to add a transducer to a slidebar, a 2-Line-LISN or 4-Line LISN. Now, I want to add a transducer for an 8-Wire ISN (e.g. ENY81) to EMC32.
¿Cómo puedo configurar un transductor válido?
EMC32, Download Transducer Factor to Test Receiver
EMC32 measurements with more than 1000000 points
FAQ: Comprobar las ampliaciones del EMC32
Esta nota de aplicación explica cómo configurar, calibrar y realizar medidas de EMS conducidas de acuerdo con IEC / EN 61000-4-6 y medidas de EMI de acuerdo con CISPR 16-2-1 con el software R&S®EMC32.
jul 19, 2013 | N.º de nota de aplicación 1MA212
EMC32, Level Sweep shape during Reference Calibration
FAQ: ¿Cuándo necesito la administración de usuarios de EMC32?
¿Es posible implementar una mesa giratoria que pueda controlar a través del software EMC32 con mi receptor EMI?
EMC32, display preview results of all LISN phases
Nivel de inmunidad no alcanzado: cancelar escaneado de EMS
Mostrar el gráfico de un transductor mediante EMC32
Envío de frecuencia y nivel del EMC32 a Vector CANoe.
How can I add a attenuation table to my cable, used in my measurement setup?
En los gráficos de un test, ¿es posible hacer que se visualice constantemente la leyenda, de forma que no sea necesario insertarla cada vez que finaliza el test?
Using R&S®ELEKTRA Migration Tool
The R&S®ELEKTRA EMC test software is the successor of the R&S®EMC32 EMC measurement software. Like the R&S®EMC32 EMC measurement software, the R&S®ELEKTRA offers a solution that controls complete EMC systems and automates measurements on equipment under test (EUT) that is being tested for emissions (EMI) and immunity (EMS) compliance. It has more features and test types compared to R&S®EMC32.As both software platforms use different file formats, R&S®EMC32 users who upgrade their existing software to the R&S®ELEKTRA platform need to perform a file conversion before migrating their data to the R&S®ELEKTRA platform. This is done by using the R&S®ELEKTRA Migration Tool, which is installed automatically with each R&S®ELEKTRA installation.This Application Note describes how to use the R&S®ELEKTRA Migration Tool (version 4.4 onwards) for converting the backup data into the XML format that can be interpreted by the R&S®ELEKTRA software. It also provides recommended conversion steps (Chapter 5) and troubleshooting tips (Chapter 6). For instructions on migrating the data using R&S®ELEKTRA Migration Tool below version 4.4, refer to the R&S®ELEKTRA user manual. For better user experience, we recommend using the latest software version for migration.This Application Note does not describe the steps to backup data using the R&S®EMC32 or R&S®ES-SCAN software. For procedures on how to do so, refer to their respective manuals.
May 04, 2023 | N.º de nota de aplicación 1SL396
Use of the ESW build in Pulse Limiter, if remote controlled by EMC32
EMC32, rangos de frecuencias en la búsqueda de máximas de subrangos
Actualización de macros de API en EMC32
Cuando ejecuto el test y retrocedo para cambiar los parámetros en la plantilla de test (Test Template), ¿cómo puedo guardar los nuevos ajustes?
Utilizo el EMC32 con test automático de interferencias electromagnéticas (EMI Auto Test) EMC32-K10 y receptor de medidas ESCI. El problema es que no puedo ejecutar medidas finales con el detector CISPR AV.